Re: [CAD_CAM_EDM_DRO] Aligning Rails (or ways) on CNC router
Posted by
castinggrain
on 2002-08-15 20:33:57 UTC
Hi Bob,
I am not sure just how "accurate" you are referring to, but IMHO this
method would be a lot more accurate than using an 8 foot level to span the
gap. One of the best methods I have ever found to level two objects that
are far apart is to use a water level. Get 10 feet of clear vinyl hose (3/8"
or larger diameter) from the hardware store and just about fill it with
water. Try to have the ends pointing straight up for at least a foot. Adjust
the hose up and down on one end until the water level on that side reaches a
reference point on one of your rails then adjust the other rail to the water
level on the other end of the hose.
Jerry
I am not sure just how "accurate" you are referring to, but IMHO this
method would be a lot more accurate than using an 8 foot level to span the
gap. One of the best methods I have ever found to level two objects that
are far apart is to use a water level. Get 10 feet of clear vinyl hose (3/8"
or larger diameter) from the hardware store and just about fill it with
water. Try to have the ends pointing straight up for at least a foot. Adjust
the hose up and down on one end until the water level on that side reaches a
reference point on one of your rails then adjust the other rail to the water
level on the other end of the hose.
Jerry
----- Original Message -----
From: "bob_santa" <bobt@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, August 15, 2002 3:40 AM
Subject: [CAD_CAM_EDM_DRO] Aligning Rails (or ways) on CNC router
> Hello Group,
> Can anyone suggest an accurate method of adustind the height (z axiz)
> of router rails that are 6-1\2 feet apart. Preferably using small hand
tools as i dont intend to buy a large surface plate to set up the ways.
> Regards
> bob_santa
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
Discussion Thread
bob_santa
2002-08-15 09:11:45 UTC
Aligning Rails (or ways) on CNC router
Bill Vance
2002-08-15 10:32:47 UTC
Re: [CAD_CAM_EDM_DRO] Aligning Rails (or ways) on CNC router
Jon Elson
2002-08-15 10:55:11 UTC
Re: [CAD_CAM_EDM_DRO] Aligning Rails (or ways) on CNC router
castinggrain
2002-08-15 20:33:57 UTC
Re: [CAD_CAM_EDM_DRO] Aligning Rails (or ways) on CNC router
Bill Vance
2002-08-15 21:43:40 UTC
Re: [CAD_CAM_EDM_DRO] Aligning Rails (or ways) on CNC router
turbulatordude
2002-08-16 04:01:42 UTC
water level ( was Re: Aligning Rails (or ways) on CNC router
Jon Elson
2002-08-16 10:09:37 UTC
Re: [CAD_CAM_EDM_DRO] water level ( was Re: Aligning Rails (or ways) on CNC router
Randy Gordon-Gilmore
2002-08-16 11:18:57 UTC
Re: [CAD_CAM_EDM_DRO] water level
Randy Gordon-Gilmore
2002-08-16 11:35:01 UTC
Another question about leveling/squaring
mayfieldtm
2002-08-16 11:37:12 UTC
master precision levels
Doug Harrison
2002-08-16 12:55:55 UTC
Re: [CAD_CAM_EDM_DRO] master precision levels
turbulatordude
2002-08-16 15:05:25 UTC
water level ( was Re: Aligning Rails (or ways) on CNC router
bob_santa
2002-08-16 17:35:24 UTC
Re: Aligning Rails (or ways) on CNC router
Jon Elson
2002-08-16 20:53:25 UTC
Re: [CAD_CAM_EDM_DRO] master precision levels
Jon Elson
2002-08-16 21:24:03 UTC
Re: [CAD_CAM_EDM_DRO] water level ( was Re: Aligning Rails (or ways) on CNC router
turbulatordude
2002-08-17 06:03:32 UTC
water level ( was Re: Aligning Rails (or ways) on CNC router
Carlos Guillermo
2002-08-27 11:04:43 UTC
RE: [CAD_CAM_EDM_DRO] master precision levels
Randy Gordon-Gilmore
2002-08-27 17:00:48 UTC
Demise of free Intellicad
Randy Gordon-Gilmore
2002-08-27 17:33:51 UTC
Re: [CAD_CAM_EDM_DRO] Demise of free Intellicad
Doug Harrison
2002-08-27 17:34:28 UTC
RE: [CAD_CAM_EDM_DRO] master precision levels
LEW BEST
2002-08-27 18:46:44 UTC
RE: [CAD_CAM_EDM_DRO] master precision levels
studleylee
2002-08-27 20:19:41 UTC
Re: master precision levels
Jeff Hamilton
2002-08-27 20:50:28 UTC
Cutting Glass scales
Dave Lantz
2002-08-28 05:21:30 UTC
RE: [CAD_CAM_EDM_DRO] Demise of free Intellicad
Kos
2002-08-29 02:36:05 UTC
Re: [CAD_CAM_EDM_DRO] Demise of free Intellicad
Randy Gordon-Gilmore
2002-08-29 14:58:53 UTC
BDI question and Knoppix plug
wanliker@a...
2002-08-29 15:22:19 UTC
Re: [CAD_CAM_EDM_DRO] BDI question and Knoppix plug
Randy Gordon-Gilmore
2002-08-29 15:33:03 UTC
Re: BDI question and Knoppix plug
William Scalione
2002-08-29 22:26:45 UTC
Re: [CAD_CAM_EDM_DRO] BDI question and Knoppix plug
Ian W. Wright
2002-08-30 01:22:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: BDI question and Knoppix plug
Ray Henry
2002-08-30 09:07:13 UTC
Re: Re: Re: BDI question and Knoppix plug
Ian W. Wright
2002-08-30 10:43:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: BDI question and Knoppix plug
Bill Vance
2002-08-30 11:55:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: BDI question and Knoppix plug
j.guenther
2002-08-30 12:05:25 UTC
RE: [CAD_CAM_EDM_DRO] Re: BDI question and Knoppix plug
jmkasunich
2002-08-30 14:21:53 UTC
EMC / BDI / Linux / RTLinux / RTAI confusion
Bill Vance
2002-08-30 14:44:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: BDI question and Knoppix plug
Randy Gordon-Gilmore
2002-08-30 22:48:43 UTC
Re: [CAD_CAM_EDM_DRO] BDI question and Knoppix plug
Jon Elson
2002-08-30 23:03:36 UTC
Re: [CAD_CAM_EDM_DRO] EMC / BDI / Linux / RTLinux / RTAI confusion
Randy Gordon-Gilmore
2002-08-31 02:15:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: BDI question and Knoppix plug
funcadem
2003-07-22 02:43:07 UTC
Re: Re: BDI question and Knoppix plug
Paul
2003-07-22 10:05:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: BDI question and Knoppix plug
funcadem
2003-07-22 13:13:53 UTC
Re: BDI question and Knoppix plug
funcadem
2003-07-22 13:20:30 UTC
Re: BDI question and Knoppix plug
Paul
2003-07-22 13:36:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: BDI question and Knoppix plug