Re: [CAD_CAM_EDM_DRO] BDI and servos
Posted by
Jon Elson
on 2002-12-06 22:02:18 UTC
Bob Simon wrote:
card, or my parallel port
motion control board set. Either gives you a +/- 10 V analog velocity
signal to drive
analog-input servo amps, and an input for quadrature encoders. All the
servo parameters
are in the setup file, and can even be tuned while running. There is a
graphing feature that
allows you to generate plots of commanded vs. actual position, so you
can adjust parameters
to get the minimum following error.
Jon
>Can the Brain Dead Install of EMC be used with analog servo systems or isNo, it has support for analog servos, too. You can use the Servo-to-Go
>it specifically set up for step and direction only?
>
>
card, or my parallel port
motion control board set. Either gives you a +/- 10 V analog velocity
signal to drive
analog-input servo amps, and an input for quadrature encoders. All the
servo parameters
are in the setup file, and can even be tuned while running. There is a
graphing feature that
allows you to generate plots of commanded vs. actual position, so you
can adjust parameters
to get the minimum following error.
Jon
Discussion Thread
Fred Smith
2002-11-29 14:53:44 UTC
DeskCNC now in beta release
Tim Goldstein
2002-11-29 17:32:30 UTC
RE: [CAD_CAM_EDM_DRO] DeskCNC now in beta release
aussiedude
2002-11-29 18:45:01 UTC
RE: [CAD_CAM_EDM_DRO] DeskCNC now in beta release
Carol & Jerry Jankura
2002-11-29 18:48:11 UTC
RE: [CAD_CAM_EDM_DRO] DeskCNC now in beta release
aussiedude
2002-11-29 19:25:17 UTC
RE: [CAD_CAM_EDM_DRO] DeskCNC Versus Master 5 / Mach 1
aussiedude
2002-11-29 19:31:19 UTC
RE: [CAD_CAM_EDM_DRO] DeskCNC Versus Master 5 / Mach 1
Tim Goldstein
2002-11-29 19:31:55 UTC
RE: [CAD_CAM_EDM_DRO] DeskCNC now in beta release
Tim Goldstein
2002-11-29 19:39:59 UTC
RE: [CAD_CAM_EDM_DRO] DeskCNC Versus Master 5 / Mach 1
Tim Goldstein
2002-11-29 19:44:02 UTC
RE: [CAD_CAM_EDM_DRO] DeskCNC Versus Master 5 / Mach 1
aussiedude
2002-11-29 19:51:43 UTC
RE: [CAD_CAM_EDM_DRO] DeskCNC Versus Master 5 / Mach 1
Tim Goldstein
2002-11-29 20:06:16 UTC
RE: [CAD_CAM_EDM_DRO] DeskCNC Versus Master 5 / Mach 1
aussiedude
2002-11-29 20:18:21 UTC
RE: [CAD_CAM_EDM_DRO] DeskCNC Versus Master 5 / Mach 1
Chris L
2002-11-29 20:27:45 UTC
Re: [CAD_CAM_EDM_DRO] DeskCNC Versus Master 5 / Mach 1
stevenson_engineers
2002-11-30 01:22:18 UTC
Re: DeskCNC Versus Master 5 / Mach 1
Jens Swales
2002-11-30 02:58:15 UTC
Re: DeskCNC Versus Master 5 / Mach 1
Chris L
2002-11-30 07:03:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: DeskCNC Versus Master 5 / Mach 1
Fred Smith
2002-12-06 08:57:36 UTC
Re: DeskCNC now in beta release
stevenson_engineers
2002-12-06 10:43:08 UTC
Re: DeskCNC now in beta release
Bob Simon
2002-12-06 11:08:53 UTC
BDI and servos
Tim Goldstein
2002-12-06 13:29:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: DeskCNC now in beta release
Jon Elson
2002-12-06 22:02:18 UTC
Re: [CAD_CAM_EDM_DRO] BDI and servos
Ray Henry
2002-12-07 07:16:47 UTC
Re: BDI and servos
Bob Simon
2002-12-07 08:39:19 UTC
Re: [CAD_CAM_EDM_DRO] BDI and servos
blown_mgb_v8 <jblackwood5@i...
2002-12-07 08:51:32 UTC
Re: BDI and servos
Bob Simon
2002-12-07 08:58:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: BDI and servos
Ray Henry
2002-12-07 17:02:43 UTC
Re: Re: BDI and servos
Ray Henry
2002-12-07 17:45:06 UTC
Re: Re: BDI and servos
Ray Henry
2002-12-07 17:45:09 UTC
Re: Re: Re: BDI and servos
Jon Elson
2002-12-07 22:10:25 UTC
Re: [CAD_CAM_EDM_DRO] BDI and servos
Jon Elson
2002-12-07 22:11:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: BDI and servos
Bob Simon
2002-12-08 11:48:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: BDI and servos
Bob Simon
2002-12-08 11:48:06 UTC
Re: [CAD_CAM_EDM_DRO] BDI and servos
Jon Elson
2002-12-08 23:09:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: BDI and servos
Jon Elson
2002-12-08 23:12:29 UTC
Re: [CAD_CAM_EDM_DRO] BDI and servos
Ray Henry
2002-12-09 05:03:02 UTC
Re: Re: Re: Re: BDI and servos
Bob Simon
2002-12-11 09:40:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: Re: BDI and servos