CAD CAM EDM DRO - Yahoo Group Archive

Re: Power supply transformer setup questions...

on 2003-09-10 07:11:58 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Lloyd Leung" <lloyd@l...>
wrote:
> Is there a method of wiring two transformers of the same voltage
together to
> increase the amperage that they can supply? If possible, how
should I wire
> this up to produce a power supply? Is this a safe idea for wiring
up gecko
> G201 drives?
>
>
>
> I'm looking to go from 50VAC to 70VDC.
>
>
>
> The three stepper motors I'm going to use are: two 3V/3Amp, one
4.2V/3.5Amp.
> The sum of amperage required for the motors is 10AMPs. So I
require 6.7amps
> (2/3rds of sum).


I'm not sure, but it seems you are using using linear math to
determine amperage.

10 amps at 1 volt is not the same as 10 amps at 20 volts.
10A@1V=10 watts, 10A@20V=200 watts !

your motors,
3A@3v = 9 watts,
3.5A@4.2v = 14.7 watts.

23.7 watts total.

jumping to 50 volts, divide watts by volts to figure amps.
That means your power supply needs to be 2.1 amps. (then less 33%)


Seems you could use a 24 V, a 12 V and a 6 volt to get close to 60
volts. and you could tap off the 12 and 6 to get 18VAC for that
additional stepper.


Dave




>
>
>
> The transformers I'm looking to _some how_ link together are:
>
> 167P50 (50VAC/5Amp)
>
>
> http://sales.digikey.com/scripts/sales.dll?
action=lineitem;itemseq=14201596
>
>
>
> 167L50 (50VAC/2AMP)
>
>
> http://sales.digikey.com/scripts/sales.dll?
action=lineitem;itemseq=14201598
>
>
>
> Additional transfers from hammond manufacturing are
listed here:
>
>
http://www.hammondmanufacturing.com/5cpwr.htm
>
>
>
>
>
> Also, there is this little vexta stepper motor I have that I may
want to use
> for a rotary table:
>
>
>
> Vexta PK569AUHA (2.8Amp/0.55 oHm (so 1.54V??))
>
>
>
> Is there a way I can add this drive into the power supply, or
should I build
> a completely different power supply for this axis? If I use 50V to
this
> little motor, it's going to cook itself.
>
>
>
>
>
> So far, I have the gecko's and the motors... I would like input on
how I
> should setup my power supply, thanks.
>
>
>
>
>
>
>
> Lloyd, in Toronto.
>
>
>
> [Non-text portions of this message have been removed]

Discussion Thread

Lloyd Leung 2003-09-10 04:28:49 UTC Power supply transformer setup questions... turbulatordude 2003-09-10 07:11:58 UTC Re: Power supply transformer setup questions... microboter 2003-09-10 07:38:44 UTC Re: Power supply transformer setup questions... Tim Goldstein 2003-09-10 08:03:11 UTC RE: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... Robert Campbell 2003-09-10 08:06:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... Tony Jeffree 2003-09-10 08:22:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... Alan Marconett KM6VV 2003-09-10 12:09:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... JanRwl@A... 2003-09-10 12:46:49 UTC Re: [CAD_CAM_EDM_DRO] Power supply transformer setup questions... Lloyd Leung 2003-09-10 14:08:21 UTC RE: Power supply transformer setup questions... Tim Goldstein 2003-09-10 14:30:23 UTC RE: [CAD_CAM_EDM_DRO] RE: Power supply transformer setup questions... turbulatordude 2003-09-10 14:30:33 UTC Re: Power supply transformer setup questions... Lloyd Leung 2003-09-10 14:47:28 UTC RE: Power supply transformer setup questions... Tony Jeffree 2003-09-10 16:19:27 UTC Re: [CAD_CAM_EDM_DRO] RE: Power supply transformer setup questions... Tony Jeffree 2003-09-10 16:25:19 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... JanRwl@A... 2003-09-10 16:58:28 UTC Re: [CAD_CAM_EDM_DRO] RE: Power supply transformer setup questions... turbulatordude 2003-09-10 18:45:13 UTC Re: Power supply transformer setup questions...Capacitors turbulatordude 2003-09-10 18:57:14 UTC Re: Power supply transformer setup questions... Antonius J.M. Groothuizen 2003-09-10 18:58:28 UTC Re: Power supply transformer setup questions...Capacitors Raymond Heckert 2003-09-10 19:05:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... JanRwl@A... 2003-09-10 19:13:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions...Capacitors JanRwl@A... 2003-09-10 19:39:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... Lloyd Leung 2003-09-10 19:54:45 UTC RE: Re: Power supply transformer setup questions...Capacitors turbulatordude 2003-09-10 20:42:49 UTC Re: Power supply transformer setup questions...Capacitors turbulatordude 2003-09-11 08:35:06 UTC Re: Power supply transformer setup questions... OPP's