Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions...
Posted by
Alan Marconett KM6VV
on 2003-09-10 12:09:34 UTC
Hi Jeff, Lloyd,
I'll have to disagree with you Jeff. if the transformers have the same
output voltage, they CAN be wired in parallel! It's done all the time.
The phase of the transformers must be observed. That is, they must be
connected such that the leads of each transformer go + at the same time,
other wise they will buck. Perhaps that is what you meant.
See my Gecko Driver/PS schematic in the files section under Driver/PS:
http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/DriverPS/
Alan KM6VV
SherlineCNC
microboter wrote:
I'll have to disagree with you Jeff. if the transformers have the same
output voltage, they CAN be wired in parallel! It's done all the time.
The phase of the transformers must be observed. That is, they must be
connected such that the leads of each transformer go + at the same time,
other wise they will buck. Perhaps that is what you meant.
See my Gecko Driver/PS schematic in the files section under Driver/PS:
http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/DriverPS/
Alan KM6VV
SherlineCNC
microboter wrote:
>
> Wiring the 2 transformers in parallel seems like a nice clean
> solution to your current problem of needing 6.7 amps to drive your
> motors.
>
> In a nutshell "NO" you can't do this. The transformers don't like
> being wired in parallel. They will for a lack of a better term buck
> each other. You will need to drive each Gecko with a separate 3 amp
> or so transformer/ power supply combo, or one large one.
>
> hth
>
> Jeff
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Lloyd Leung" <lloyd@l... wrote:
> > Is there a method of wiring two transformers of the same voltage together to
> > increase the amperage that they can supply? If possible, how should I wire
> > this up to produce a power supply? Is this a safe idea for wiring up gecko
> > G201 drives?
> >
> > I'm looking to go from 50VAC to 70VDC.
> >
> > The three stepper motors I'm going to use are: two 3V/3Amp, one 4.2V/3.5Amp.
> > The sum of amperage required for the motors is 10AMPs. So I require 6.7amps
> > (2/3rds of sum).
> >
> > <SNIP>
> >
> > So far, I have the gecko's and the motors... I would like input on
> how I
> > should setup my power supply, thanks.
> >
> >
> >
> > Lloyd, in Toronto.
Discussion Thread
Lloyd Leung
2003-09-10 04:28:49 UTC
Power supply transformer setup questions...
turbulatordude
2003-09-10 07:11:58 UTC
Re: Power supply transformer setup questions...
microboter
2003-09-10 07:38:44 UTC
Re: Power supply transformer setup questions...
Tim Goldstein
2003-09-10 08:03:11 UTC
RE: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions...
Robert Campbell
2003-09-10 08:06:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions...
Tony Jeffree
2003-09-10 08:22:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions...
Alan Marconett KM6VV
2003-09-10 12:09:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions...
JanRwl@A...
2003-09-10 12:46:49 UTC
Re: [CAD_CAM_EDM_DRO] Power supply transformer setup questions...
Lloyd Leung
2003-09-10 14:08:21 UTC
RE: Power supply transformer setup questions...
Tim Goldstein
2003-09-10 14:30:23 UTC
RE: [CAD_CAM_EDM_DRO] RE: Power supply transformer setup questions...
turbulatordude
2003-09-10 14:30:33 UTC
Re: Power supply transformer setup questions...
Lloyd Leung
2003-09-10 14:47:28 UTC
RE: Power supply transformer setup questions...
Tony Jeffree
2003-09-10 16:19:27 UTC
Re: [CAD_CAM_EDM_DRO] RE: Power supply transformer setup questions...
Tony Jeffree
2003-09-10 16:25:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions...
JanRwl@A...
2003-09-10 16:58:28 UTC
Re: [CAD_CAM_EDM_DRO] RE: Power supply transformer setup questions...
turbulatordude
2003-09-10 18:45:13 UTC
Re: Power supply transformer setup questions...Capacitors
turbulatordude
2003-09-10 18:57:14 UTC
Re: Power supply transformer setup questions...
Antonius J.M. Groothuizen
2003-09-10 18:58:28 UTC
Re: Power supply transformer setup questions...Capacitors
Raymond Heckert
2003-09-10 19:05:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions...
JanRwl@A...
2003-09-10 19:13:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions...Capacitors
JanRwl@A...
2003-09-10 19:39:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions...
Lloyd Leung
2003-09-10 19:54:45 UTC
RE: Re: Power supply transformer setup questions...Capacitors
turbulatordude
2003-09-10 20:42:49 UTC
Re: Power supply transformer setup questions...Capacitors
turbulatordude
2003-09-11 08:35:06 UTC
Re: Power supply transformer setup questions... OPP's