CAD CAM EDM DRO - Yahoo Group Archive

Re: Power supply transformer setup questions...

on 2003-09-10 18:57:14 UTC
> >
> >look at the total watts of the motors.
> >
> >The chopper drivers cannot supply more, even if you have such an
over
> >sized power supply.
> >
> >one motor is 9 watts
> >the other 2 total 29.4 watts for a grand total of 38.4 watts.
>
> You've lost a factor of 2 here - both coils get energised in each
motor, so
> the right number is 76.8 Watts.
>
> Regards,
> Tony
>
>
> >if you run at 60 volts, then the required current is 2.04 amps for
> >ALL 3 motors.
>
> Not quite - not sure where that came from. Current is Watts divided
by
> Volts. So 76.8/60 or 1.28 Amps is nearer the mark.


Using my origional post was wrong in that I used one the 29.4 watts
from the two 3.5 amp motors. 60 volts / 29.4 = 2.04

flipping between the spreadsheet and yahoo and rushing out to a
jobsite made for less than optimum conditions.


I'm going to have to go back and read some posts to get the power to
each coil part correct. I thought I had been correct that only one
coil FLA was used for sizing the power supply as both coils will
never be charged 100%, but rather some varying percentages that don't
exceed the FLA.

Dave


>
>
> >If you want to run 6.7 amps, you will have pleanty reserve.
> >
>
> That's certainly true!
>
>
> Regards,
> Tony

Discussion Thread

Lloyd Leung 2003-09-10 04:28:49 UTC Power supply transformer setup questions... turbulatordude 2003-09-10 07:11:58 UTC Re: Power supply transformer setup questions... microboter 2003-09-10 07:38:44 UTC Re: Power supply transformer setup questions... Tim Goldstein 2003-09-10 08:03:11 UTC RE: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... Robert Campbell 2003-09-10 08:06:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... Tony Jeffree 2003-09-10 08:22:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... Alan Marconett KM6VV 2003-09-10 12:09:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... JanRwl@A... 2003-09-10 12:46:49 UTC Re: [CAD_CAM_EDM_DRO] Power supply transformer setup questions... Lloyd Leung 2003-09-10 14:08:21 UTC RE: Power supply transformer setup questions... Tim Goldstein 2003-09-10 14:30:23 UTC RE: [CAD_CAM_EDM_DRO] RE: Power supply transformer setup questions... turbulatordude 2003-09-10 14:30:33 UTC Re: Power supply transformer setup questions... Lloyd Leung 2003-09-10 14:47:28 UTC RE: Power supply transformer setup questions... Tony Jeffree 2003-09-10 16:19:27 UTC Re: [CAD_CAM_EDM_DRO] RE: Power supply transformer setup questions... Tony Jeffree 2003-09-10 16:25:19 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... JanRwl@A... 2003-09-10 16:58:28 UTC Re: [CAD_CAM_EDM_DRO] RE: Power supply transformer setup questions... turbulatordude 2003-09-10 18:45:13 UTC Re: Power supply transformer setup questions...Capacitors turbulatordude 2003-09-10 18:57:14 UTC Re: Power supply transformer setup questions... Antonius J.M. Groothuizen 2003-09-10 18:58:28 UTC Re: Power supply transformer setup questions...Capacitors Raymond Heckert 2003-09-10 19:05:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... JanRwl@A... 2003-09-10 19:13:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions...Capacitors JanRwl@A... 2003-09-10 19:39:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply transformer setup questions... Lloyd Leung 2003-09-10 19:54:45 UTC RE: Re: Power supply transformer setup questions...Capacitors turbulatordude 2003-09-10 20:42:49 UTC Re: Power supply transformer setup questions...Capacitors turbulatordude 2003-09-11 08:35:06 UTC Re: Power supply transformer setup questions... OPP's