CAD CAM EDM DRO - Yahoo Group Archive

Re: DYNA 2400 SOFTWARE

Posted by jeff_birt2000
on 2003-09-23 06:01:59 UTC
David,

I wound up ordering the batteries (the one in the dm3000 lath
controller was low too) from Dyna before seeing you note. They are
$38.00 from Dyna.

I tried replacing the previous code to generate an arc with an ARC
frame but have the same problem; it works great when the whole
program is downloaded but goes crazey in line execute mode. I also
found some paperwork yesterday indicating there may be a 'Block
Execute mode' available with the correct firmware version. I'll call
Dyna and inquire.

Jeff

--- In CAD_CAM_EDM_DRO@yahoogroups.com, "mrdavidpontes"
<mrdavidpontes@a...> wrote:
> ---Hi Jeff,
>
> On your comments about the battery, one can be had from ACCESS
> BATTERY, 1-800-373-3301, COST AT $32.75 EA.+ U.P.S. Battery part
> #BCX72PC,and they are for most of the Dyna 2xxx,3xxx,4xxx, controls.
>
> The battery solider on the PCB,so those that are weak hearted,
have
> someone do it for you! I have not received my batterys yet,I will
let
> the GROUP know what happens after----? I also been having some
> strange results, GHOST?
> david pontes
> mrdavidpontes@c...

Discussion Thread

mrdavidpontes 2003-09-12 23:32:44 UTC DYNA 2400 SOFTWARE jeff_birt2000 2003-09-13 07:47:36 UTC Re: DYNA 2400 SOFTWARE jeff_birt2000 2003-09-13 23:36:12 UTC Re: DYNA 2400 SOFTWARE R Homer 2003-09-16 08:00:22 UTC Re: [CAD_CAM_EDM_DRO] Re: DYNA 2400 SOFTWARE jeff_birt2000 2003-09-17 00:14:17 UTC Re: DYNA 2400 SOFTWARE bank haam 2003-09-17 00:14:36 UTC Re: [CAD_CAM_EDM_DRO] Re: DYNA 2400 SOFTWARE jeff_birt2000 2003-09-17 00:15:10 UTC Re: DYNA 2400 SOFTWARE bank haam 2003-09-17 15:00:45 UTC Re: [CAD_CAM_EDM_DRO] Re: DYNA 2400 SOFTWARE jeff_birt2000 2003-09-17 23:45:33 UTC Re: DYNA 2400 SOFTWARE bank haam 2003-09-18 11:42:54 UTC Re: [CAD_CAM_EDM_DRO] Re: DYNA 2400 SOFTWARE jeff_birt2000 2003-09-19 06:59:20 UTC Re: DYNA 2400 SOFTWARE mrdavidpontes 2003-09-19 10:34:25 UTC Re: DYNA 2400 SOFTWARE bank haam 2003-09-20 07:56:46 UTC Re: [CAD_CAM_EDM_DRO] Re: DYNA 2400 SOFTWARE jeff_birt2000 2003-09-23 06:01:59 UTC Re: DYNA 2400 SOFTWARE jeff_birt2000 2003-09-25 15:42:29 UTC Re: DYNA 2400 SOFTWARE jeff_birt2000 2003-09-25 19:30:06 UTC Re: DYNA 2400 SOFTWARE bank haam 2003-09-26 07:11:26 UTC Re: [CAD_CAM_EDM_DRO] Re: DYNA 2400 SOFTWARE jeff_birt2000 2003-09-26 17:40:52 UTC Re: DYNA 2400 SOFTWARE mrdavidpontes 2003-09-26 23:36:49 UTC Re: DYNA 2400 SOFTWARE jeff_birt2000 2003-09-27 20:13:10 UTC Re: DYNA 2400 SOFTWARE