CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] DenverCNC?

Posted by Tim Goldstein
on 2003-10-27 16:48:05 UTC
> -----Original Message-----
> Tim,
>
> Most of my experience has come from 1/2 step drives so some
> of my comments may not be relevant to a micro stepping drive.
>
> I am sure that the DenverCNC system and the 114oz/in motors
> have been thoroughly tested by yourself and others, and has
> been found to be a good match with the Taig mill.
>
> Therefore I shall stand (or sit) corrected.

Dan Statman has posted a number of times about the tremendous
improvement in his Sherline mill performance when he sent from half step
drives to 8X microstepping. The reduction or elimination in resonance
yields amazing improvement in performance with the same motors.

Tim
[Denver, CO]
Sherline & Taig products at Deep Discount
Mach1 & DeskCNC with credit card ordering
www.KTMarketing.com/Sherline
e-mail me at Timg @ KTMarketing.com for items not yet listed

Discussion Thread

Mike McCaughey 2003-10-24 09:32:45 UTC DenverCNC? Tim Goldstein 2003-10-24 10:20:09 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? William Schmiedlin 2003-10-24 15:36:01 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Kim Lux 2003-10-24 15:36:58 UTC Threadmilling success... Tim Goldstein 2003-10-24 16:19:54 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Jason Cox 2003-10-24 16:20:02 UTC Re: [CAD_CAM_EDM_DRO] Threadmilling success... Jason Cox 2003-10-24 16:23:57 UTC Re: [CAD_CAM_EDM_DRO] Threadmilling success... Derek B. 2003-10-26 23:14:04 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Peter Homann 2003-10-27 00:16:08 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Tony Jeffree 2003-10-27 00:35:27 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Derek B. 2003-10-27 09:11:22 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Peter Homann 2003-10-27 15:12:03 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Tim Goldstein 2003-10-27 15:59:43 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Peter Homann 2003-10-27 16:44:31 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Tim Goldstein 2003-10-27 16:48:05 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Statman Designs, LLC 2003-10-27 21:21:09 UTC Re: [CAD_CAM_EDM_DRO] DenverCNC? ballendo 2003-10-28 00:25:47 UTC Re: DenverCNC? Derek B. 2003-10-28 06:49:35 UTC RE: [CAD_CAM_EDM_DRO] Re: DenverCNC? Tim Goldstein 2003-10-28 07:39:05 UTC RE: [CAD_CAM_EDM_DRO] Re: DenverCNC? ballendo 2003-10-29 06:37:26 UTC OT thank you was Re: DenverCNC? ballendo 2003-10-29 06:39:25 UTC OT thank you was Re: DenverCNC?