OT thank you was Re: DenverCNC?
Posted by
ballendo
on 2003-10-29 06:39:25 UTC
Tim,
Thank you for the additional details...
Ballendo
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Tim Goldstein" <timg@k...>
wrote:
Thank you for the additional details...
Ballendo
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Tim Goldstein" <timg@k...>
wrote:
> Ballendo,with
>
> Whoops, I was suppose to get back to you with that.
>
> It is a 4 amp supply and it is using a Xylotex board set. They did
> extensive testing at various voltages and with various motors. Even
> the current maxed out it never drew over 4 amps and usually wellunder.
>
> Tim
> [Denver, CO]
> Sherline & Taig products at Deep Discount
> Mach1 & DeskCNC with credit card ordering
> www.KTMarketing.com/Sherline
> e-mail me at Timg @ KTMarketing.com for items not yet listed
Discussion Thread
Mike McCaughey
2003-10-24 09:32:45 UTC
DenverCNC?
Tim Goldstein
2003-10-24 10:20:09 UTC
RE: [CAD_CAM_EDM_DRO] DenverCNC?
William Schmiedlin
2003-10-24 15:36:01 UTC
RE: [CAD_CAM_EDM_DRO] DenverCNC?
Kim Lux
2003-10-24 15:36:58 UTC
Threadmilling success...
Tim Goldstein
2003-10-24 16:19:54 UTC
RE: [CAD_CAM_EDM_DRO] DenverCNC?
Jason Cox
2003-10-24 16:20:02 UTC
Re: [CAD_CAM_EDM_DRO] Threadmilling success...
Jason Cox
2003-10-24 16:23:57 UTC
Re: [CAD_CAM_EDM_DRO] Threadmilling success...
Derek B.
2003-10-26 23:14:04 UTC
RE: [CAD_CAM_EDM_DRO] DenverCNC?
Peter Homann
2003-10-27 00:16:08 UTC
RE: [CAD_CAM_EDM_DRO] DenverCNC?
Tony Jeffree
2003-10-27 00:35:27 UTC
RE: [CAD_CAM_EDM_DRO] DenverCNC?
Derek B.
2003-10-27 09:11:22 UTC
RE: [CAD_CAM_EDM_DRO] DenverCNC?
Peter Homann
2003-10-27 15:12:03 UTC
RE: [CAD_CAM_EDM_DRO] DenverCNC?
Tim Goldstein
2003-10-27 15:59:43 UTC
RE: [CAD_CAM_EDM_DRO] DenverCNC?
Peter Homann
2003-10-27 16:44:31 UTC
RE: [CAD_CAM_EDM_DRO] DenverCNC?
Tim Goldstein
2003-10-27 16:48:05 UTC
RE: [CAD_CAM_EDM_DRO] DenverCNC?
Statman Designs, LLC
2003-10-27 21:21:09 UTC
Re: [CAD_CAM_EDM_DRO] DenverCNC?
ballendo
2003-10-28 00:25:47 UTC
Re: DenverCNC?
Derek B.
2003-10-28 06:49:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: DenverCNC?
Tim Goldstein
2003-10-28 07:39:05 UTC
RE: [CAD_CAM_EDM_DRO] Re: DenverCNC?
ballendo
2003-10-29 06:37:26 UTC
OT thank you was Re: DenverCNC?
ballendo
2003-10-29 06:39:25 UTC
OT thank you was Re: DenverCNC?