CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: DenverCNC?

Posted by Tim Goldstein
on 2003-10-28 07:39:05 UTC
Ballendo,

Whoops, I was suppose to get back to you with that.

It is a 4 amp supply and it is using a Xylotex board set. They did
extensive testing at various voltages and with various motors. Even with
the current maxed out it never drew over 4 amps and usually well under.

Tim
[Denver, CO]
Sherline & Taig products at Deep Discount
Mach1 & DeskCNC with credit card ordering
www.KTMarketing.com/Sherline
e-mail me at Timg @ KTMarketing.com for items not yet listed

Discussion Thread

Mike McCaughey 2003-10-24 09:32:45 UTC DenverCNC? Tim Goldstein 2003-10-24 10:20:09 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? William Schmiedlin 2003-10-24 15:36:01 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Kim Lux 2003-10-24 15:36:58 UTC Threadmilling success... Tim Goldstein 2003-10-24 16:19:54 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Jason Cox 2003-10-24 16:20:02 UTC Re: [CAD_CAM_EDM_DRO] Threadmilling success... Jason Cox 2003-10-24 16:23:57 UTC Re: [CAD_CAM_EDM_DRO] Threadmilling success... Derek B. 2003-10-26 23:14:04 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Peter Homann 2003-10-27 00:16:08 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Tony Jeffree 2003-10-27 00:35:27 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Derek B. 2003-10-27 09:11:22 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Peter Homann 2003-10-27 15:12:03 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Tim Goldstein 2003-10-27 15:59:43 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Peter Homann 2003-10-27 16:44:31 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Tim Goldstein 2003-10-27 16:48:05 UTC RE: [CAD_CAM_EDM_DRO] DenverCNC? Statman Designs, LLC 2003-10-27 21:21:09 UTC Re: [CAD_CAM_EDM_DRO] DenverCNC? ballendo 2003-10-28 00:25:47 UTC Re: DenverCNC? Derek B. 2003-10-28 06:49:35 UTC RE: [CAD_CAM_EDM_DRO] Re: DenverCNC? Tim Goldstein 2003-10-28 07:39:05 UTC RE: [CAD_CAM_EDM_DRO] Re: DenverCNC? ballendo 2003-10-29 06:37:26 UTC OT thank you was Re: DenverCNC? ballendo 2003-10-29 06:39:25 UTC OT thank you was Re: DenverCNC?