RE: [CAD_CAM_EDM_DRO] port problem

Are you running Mach2 or Mach3?

Andy Wander
Verrex Corporation


-----Original Message-----
From: John D. Bussema [mailto:bussema@...]
Sent: Wednesday, October 27, 2004 10:29 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] port problem


Mach2 is has step/direction output by default, right? I cant find anywhere
to change this so I must assume. . . Everything else you mentioned I have
setup properly, I think.

-John

----- Original Message -----
From: "Andy Wander" <awander@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, October 27, 2004 8:58 PM
Subject: RE: [CAD_CAM_EDM_DRO] port problem


>
> Your'e on the right track with the voltages you're trying to measure on
> the
> Dir pin.
>
> Make sure that Mach2 is set up to point to the address of the port(first
> page of Config/Ports& Pins), and that the port is enabled.
>
> Make sure that Mach2 is set up to output the Step and Dir signals for at
> least one motor, and that the port/pin settings are correct for those
> outputs.
>
> Make sure that Mach2 has the outputrs set to "Active Low.
>
> Make sure you have run +5V to the Gecko Commons.
>
> Andy Wander
> Verrex Corporation
>
>
> -----Original Message-----
> From: John D. Bussema [mailto:bussema@...]
> Sent: Wednesday, October 27, 2004 9:45 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] port problem
>
>
> Howdy,
>
> I'm having some trouble interfacing my PC to my set of G320's. I have one
> drive fully wired to a servo, and I'm trying to use Mach2 to get the thing
> to spin. I installed Mach2 and set it to output step to pin 1 of the
> parellel port and direction to pin 2. After trying to jog the servo for a
> while with no success, I decided to check into problems I might have with
> the parellel port. The first obvious one I found was that it wasn't
> enabled
> in the bios. . . so I of course enabled it, happy that I had most likely
> solved the problem. Unfortunatly that wasn't it. My first question is if
> there is any simple way to test output. Lacking a scope, I tried testing
> the
>
> logic level of the direction pin as I "jog" Mach2 in different
> dirrections.
> I would expect to see something around 0 volts for one direction and
> something around 5 volts for the other. . . right? My other question I
> guess
>
> is if there is some common problem I could be overlooking. Anyone have a
> simple fix?
>
> Thanks,
> John
> ----- Original Message -----
> From: <JanRwl@...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Wednesday, October 27, 2004 8:24 PM
> Subject: Re: [CAD_CAM_EDM_DRO] rotary table as 4th axis
>
>
>>
>>
>> In a message dated 10/27/2004 10:20:24 AM Central Standard Time,
>> rogerstykle@... writes:
>>
>> has anyone here been able to convert a regular 6" 8" rotary table to
>> cnc? I dont have a rotary table so I dont know if it's possible to get
>> all or at least most of the backlash out. Im thinking about purchasing
>> one but would like to see if you can do it before I spend the money.
>>
>>
>>
>>
>> I once built a circuit to drive a stepper from a PC, the whole "set"
>> connected to a Bridgeport mill's computer, making the 4th axis. The
>> user-shop
>> attached the stepper I provided to their 10 or 12" rotary table. I
>> don't
>
>> recall
>> any discussion about backlash. I THINK there was no concern about this,
>> as
>> the accessory was always used rotating in ONE direction. Simple,
>> really.
>>
>>
>> [Non-text portions of this message have been removed]
>>
>>
>>
>> Addresses:
>> FAQ: http://www.ktmarketing.com/faq.html
>> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>>
>> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
>> timg@...
>> Moderator: pentam@... indigo_red@... davemucha@...
>> [Moderators]
>> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>>
>> OFF Topic POSTS: General Machining
>> If you wish to post on unlimited OT subjects goto:
>> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
>> if you have trouble.
>> http://www.metalworking.com/news_servers.html
>>
>> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
>> sister site to the CCED group, as many of the same members are there, for
>> OT subjects, that are not allowed on the CCED list.
>>
>> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
>> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>> bill
>> List Mom
>> List Owner
>>
>>
>> Yahoo! Groups Links
>>
>>
>>
>>
>>
>>
>>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> if
> you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for
> OT
> subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for
> OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>



Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner


Yahoo! Groups Links