Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
Posted by
Peter Homann
on 2004-12-03 18:28:41 UTC
Mariss,
I should have realised you had it covered. :-)
Peter.
Mariss Freimanis wrote:
------------------------------------------------------------------
Web: www.homanndesigns.com
email: homann@...
Phone: +61 421 601 665
www.homanndesigns.com/DigiSpeedDeal.html - DC Spindle control
www.homanndesigns.com/TurboTaig.html - Taig Mill Upgrade board
I should have realised you had it covered. :-)
Peter.
Mariss Freimanis wrote:
>--
> Peter,
>
> Not a problem, 100mA is current to spare. The 100mA outputs are open-
> drain and diode clamped to the 24VDC power supply of your choice. You
> supply the 24VDC to run your relays or whatever, that is not taken
> from the USB 5VDC.
>
> Mariss
>
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, Peter Homann <groups@h...>
> wrote:
>
>>Hi Mariss,
>>
>>You will need to add an alternative power source, such as a wall
>
> adapter
>
>>or other power supply. The USB specification imposes limits on
>
> current
>
>>draw. The host first recognizes any peripheral as a low-power
>
> device,
>
>>which is limited to less than 100 mA of current. The peripheral can
>
> ask
>
>>the host to recognize it as a high-power device through a process
>
> called
>
>>enumeration. Once enumeration is complete and permission is
>
> granted, the
>
>>peripheral current limitation increases to 500 mA.
>>
>>Even 500mA is not enough for 16 outputs at 100mA each, let alone
>
> the
>
>>other power requirements of the G2002.
>>
>>Cheers,
>>
>>Peter.
>>
>>Mariss Freimanis wrote:
>>
>>>Hi,
>>>
>>>The G204V "Vampire" drive design is finished. The first 100 beta
>>>units will be available at the beginning of January.
>>>
>>>That means I'm back on the G2002 (G2005?) project. The FPGA for
>
> the
>
>>>design is being coded right now. In summary, the G2002 will have:
>>>
>>>1) 6 axis of step / direction (up to 4 MHz step rate)
>>>2) 6 axies of encoder feedback (CH-A, CH-B, Index and Fault)
>>>3) 8 analog output channels (+/-10V, 0-5V)
>>>4) 8 analog input channels (0-5V)
>>>5) 16 general purpose outputs (5-24VDC, 100mA)
>>>6) 16 general purpose inputs (+/- 100V protected)
>>>7) USB interface, USB powered
>>>
>>>Mariss
>>>
>>>
>>>
>>>--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...>
>
> wrote:
>
>>>>R Rogers wrote:
>>>>
>>>>
>>>>
>>>>>Wasn't Art Fenerty working on a system like this for Mach2? He
>>>
>>>referred to it as a "cube" or something like that? Basically a
>
> remote
>
>>>pulse generator. However, I understood it was to work from the
>>>parallel port. Maybe he already released it and I'm unaware of
>
> it.
>
>>>>>
>>>>Yes, hardware by Mariss Freimanis of Gecko Drives, called the
>>>
>>>G2002, I
>>>
>>>
>>>>think. There is a group
>>>>of people working on it. It runs through the USB, I believe.
>>>>
>>>>Jon
>>>
>>>
>>>
>>>
>>>
>>>
>>>Addresses:
>>>FAQ: http://www.ktmarketing.com/faq.html
>>>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>>>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>>>
>>>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>>>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>>>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
>
> wanliker@a..., timg@k...
>
>>>Moderator: pentam@c... indigo_red@q... davemucha@j...
>
> [Moderators]
>
>>>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>>>
>>>OFF Topic POSTS: General Machining
>>>If you wish to post on unlimited OT subjects goto:
>
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach
> it if you have trouble.
>
>>>http://www.metalworking.com/news_servers.html
>>>
>>>http://groups.yahoo.com/group/jobshophomeshop I consider this
>
> to be a sister site to the CCED group, as many of the same members
> are there, for OT subjects, that are not allowed on the CCED list.
>
>>>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
>
> POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> EXCEPTIONS........
>
>>>bill
>>>List Mom
>>>List Owner
>>>
>>>
>>>Yahoo! Groups Links
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>
>>--
>>------------------------------------------------------------------
>>Web: www.homanndesigns.com
>>email: homann@h...
>>Phone: +61 421 601 665
>>www.homanndesigns.com/DigiSpeedDeal.html - DC Spindle control
>>www.homanndesigns.com/TurboTaig.html - Taig Mill Upgrade board
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
> Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
>
>
------------------------------------------------------------------
Web: www.homanndesigns.com
email: homann@...
Phone: +61 421 601 665
www.homanndesigns.com/DigiSpeedDeal.html - DC Spindle control
www.homanndesigns.com/TurboTaig.html - Taig Mill Upgrade board
Discussion Thread
salsaman59@s...
2004-12-01 21:44:45 UTC
USB ports ?
Kim Lux
2004-12-02 07:11:56 UTC
Re: [CAD_CAM_EDM_DRO] USB ports ?
turbulatordude
2004-12-02 08:17:48 UTC
Re: USB ports ?
Paul
2004-12-02 08:39:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
Fred Smith
2004-12-02 08:42:56 UTC
Re: USB ports ?
Kim Lux
2004-12-02 10:13:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
turbulatordude
2004-12-02 10:32:38 UTC
Re: USB ports ?
R Rogers
2004-12-02 13:41:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
Stephen Wille Padnos
2004-12-02 17:17:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
R Rogers
2004-12-02 18:08:09 UTC
[CAD_CAM_EDM_DRO] Runaway servo questions
A. G. Eckstein
2004-12-02 18:37:04 UTC
Re: [CAD_CAM_EDM_DRO] Runaway servo questions
Jon Elson
2004-12-02 21:39:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
Jon Elson
2004-12-02 22:00:34 UTC
Re: [CAD_CAM_EDM_DRO] Runaway servo questions
Mariss Freimanis
2004-12-03 07:43:07 UTC
Re: USB ports ?
Kim Lux
2004-12-03 08:40:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: G2002, was Re: USB ports ?
Mariss Freimanis
2004-12-03 08:50:56 UTC
G2002, was Re: USB ports ?
Kim Lux
2004-12-03 15:21:17 UTC
Re: [CAD_CAM_EDM_DRO] G2002, was Re: USB ports ?
Peter Homann
2004-12-03 18:16:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
Mariss Freimanis
2004-12-03 18:26:04 UTC
Re: USB ports ?
Peter Homann
2004-12-03 18:28:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
Mariss Freimanis
2004-12-03 19:32:32 UTC
Re: USB ports ?
salsaman59@s...
2004-12-03 22:49:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
turbulatordude
2004-12-03 22:58:47 UTC
Re: USB ports ?
turbulatordude
2004-12-03 23:03:29 UTC
Re: USB ports ? Unstallable stepper ?
Mariss Freimanis
2004-12-04 00:40:22 UTC
Re: USB ports ?
turbulatordude
2004-12-04 02:36:35 UTC
Re: USB ports ?
ballendo
2004-12-04 21:15:16 UTC
Re: USB ports ? Unstallable stepper ?
ballendo
2004-12-04 21:15:18 UTC
G200X schematics? was Re: USB ports ?
Mariss Freimanis
2004-12-05 08:19:15 UTC
G200X schematics? was Re: USB ports ?
John
2004-12-05 13:53:59 UTC
Re: USB ports ?
Mariss Freimanis
2004-12-05 14:07:36 UTC
Re: USB ports ?
ballendo
2004-12-05 14:47:56 UTC
G200X schematics? was Re: USB ports ?
ballendo
2004-12-05 14:49:02 UTC
Re: USB ports ?
Mariss Freimanis
2004-12-05 16:59:32 UTC
G200X schematics? was Re: USB ports ?
Peter Reilley
2004-12-06 08:55:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
Raymond Heckert
2004-12-06 17:31:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
Peter Homann
2004-12-06 17:54:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
Tony Jeffree
2004-12-06 23:45:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?
John Heritage
2004-12-07 08:52:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB ports ?