Re: [CAD_CAM_EDM_DRO] best type of hub for pulleyts
Posted by
Jon Elson
on 2005-01-13 18:26:52 UTC
turbulatordude wrote:
some of them, others I used basically as is. This was on a 150-Lb
mini-mill,
bit I think if you select the belt correctly for the loads applied, then the
steel pulleys will be fine.
you can use
two setscrews, one on top of the other, to prevent any loosening.
Jon
>Hi all,I used XL pulleys from McMaster-Carr, and they worked fine. I modified
>
>looking for a XL pulley and it seems they come with a standard bore
>that uses set screws, or a type called a Fairloc which looks like an
>angled clamp with a screw that clamps on the shaft.
>
>
some of them, others I used basically as is. This was on a 150-Lb
mini-mill,
bit I think if you select the belt correctly for the loads applied, then the
steel pulleys will be fine.
>I'm not sure if the forces are too high or if these styles are fine.Two flats at 90 degrees is best. if there is enough meat on the hub,
>
>I am hoping that I can get a secure clamping action and not dig the
>shaft like set screws. I could file a flat if that would work. but
>cannot do a keyway.
>
>
you can use
two setscrews, one on top of the other, to prevent any loosening.
>I am not sure how much pressure the plastic pulleys can handle withI'd avoid the plastic ones except on the lightest machines (Sherline, Taig).
>the pressed in hub.
>
>
Jon
Discussion Thread
turbulatordude
2005-01-13 11:54:42 UTC
best type of hub for pulleyts
lathehand_2
2005-01-13 13:29:51 UTC
Re: best type of hub for pulleyts
R Rogers
2005-01-13 15:40:03 UTC
Re: [CAD_CAM_EDM_DRO] best type of hub for pulleyts
turbulatordude
2005-01-13 17:03:45 UTC
Re: best type of hub for pulleyts
c_holm10017
2005-01-13 18:16:37 UTC
Re: best type of hub for pulleyts (DONT USE A KEY)
Jon Elson
2005-01-13 18:26:52 UTC
Re: [CAD_CAM_EDM_DRO] best type of hub for pulleyts
turbulatordude
2005-01-13 18:38:49 UTC
Re: best type of hub for pulleyts (DONT USE A KEY)
erie
2005-01-13 19:56:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: best type of hub for pulleyts (DONT USE A KEY)
turbulatordude
2005-01-13 20:08:22 UTC
Re: best type of hub for pulleyts (DONT USE A KEY)
erie@s...
2005-01-13 21:41:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: best type of hub for pulleyts (DONT USE A KEY)
Jon Elson
2005-01-13 22:02:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: best type of hub for pulleyts (DONT USE A KEY)
Les Newell
2005-01-14 06:10:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: best type of hub for pulleyts (DONT USE A KEY)
turbulatordude
2005-01-14 07:30:50 UTC
Re: best type of hub for pulley - taper lock
lathehand_2
2005-01-14 14:21:23 UTC
Re: best type of hub for pulley - taper lock
John Dammeyer
2005-01-14 14:39:39 UTC
RE: [CAD_CAM_EDM_DRO] Re: best type of hub for pulley - taper lock
lathehand_2
2005-01-14 15:08:41 UTC
Re: best type of hub for pulley - taper lock
volitan712003
2005-01-14 15:52:12 UTC
Re: best type of hub for pulleyts (DONT USE A KEY)
grouchy_old_fred
2005-01-15 08:24:11 UTC
Re: best type of hub for pulleyts (DONT USE A KEY)
Jon Elson
2005-01-15 11:32:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: best type of hub for pulleyts (DONT USE A KEY)
turbulatordude
2005-01-15 14:14:22 UTC
Re: best type of hub for pulleyts (DONT USE A KEY)
Torsten
2005-01-16 13:56:42 UTC
Re: best type of hub for pulleyts (DONT USE A KEY)
Rod McBeath
2005-01-16 22:25:54 UTC
Re: best type of hub for pulleyts (DONT USE A KEY)
turbulatordude
2005-01-22 06:05:36 UTC
Re: best type of hub for pulleyts (DONT USE A KEY)
Jon Elson
2005-01-22 11:13:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: best type of hub for pulleyts (DONT USE A KEY)
Alan Marconett
2005-01-22 11:32:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: best type of hub for pulleyts (DONT USE A KEY)