Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
Posted by
Jon Elson
on 2005-01-31 10:17:20 UTC
Dan Mauch wrote:
Most motors with ball bearings have a preload spring (wave washer) to
constrain
the armature. A sleeve-bearing motor would not, but it is a poor choice
for a
positioning servo anyway.
Jon
>Not sure why you replied with your comments about leadscrew axial thrust. MyA lot of people try to get away with using the motor as the thrust bearing.
>statement was only a general statement that a PDMC motor should not have
>more then .005 because of the effects on encoders. It was meant as a heads
>up for when they are looking to purchase a PMDC motor for use in any servo
>applications. You are correct that motor bearings should not be used to
>handle the axial load of a leadscrew
>
Most motors with ball bearings have a preload spring (wave washer) to
constrain
the armature. A sleeve-bearing motor would not, but it is a poor choice
for a
positioning servo anyway.
Jon
Discussion Thread
braidmeister
2005-01-28 12:40:56 UTC
Bridgeport retrofit servo questions
Les Newell
2005-01-28 15:41:29 UTC
Re: [CAD_CAM_EDM_DRO] Bridgeport retrofit servo questions
braidmeister
2005-01-28 15:59:12 UTC
Re: Bridgeport retrofit servo questions
Les Newell
2005-01-28 18:35:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
braidmeister
2005-01-28 19:09:59 UTC
Re: Bridgeport retrofit servo questions
Mariss Freimanis
2005-01-28 19:57:03 UTC
Re: Bridgeport retrofit servo questions
cnc_4_me
2005-01-28 20:17:01 UTC
Re: Bridgeport retrofit servo questions
braidmeister
2005-01-28 21:04:47 UTC
Re: Bridgeport retrofit servo questions
Mariss Freimanis
2005-01-28 22:47:54 UTC
Re: Bridgeport retrofit servo questions
Les Newell
2005-01-29 02:54:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
Les Newell
2005-01-29 03:42:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
Les Newell
2005-01-29 03:49:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
AbbyKatt
2005-01-29 04:59:52 UTC
Max voltage for a stepper motor?
washcomp
2005-01-29 06:18:26 UTC
Re: Bridgeport retrofit servo questions
turbulatordude
2005-01-29 07:23:32 UTC
Re: Max voltage for a stepper motor?
braidmeister
2005-01-29 08:23:15 UTC
Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 08:44:59 UTC
Re: Bridgeport retrofit servo questions
Fred Smith
2005-01-29 08:55:24 UTC
Re: Bridgeport retrofit servo questions
Luke1027
2005-01-29 10:30:01 UTC
Re: [CAD_CAM_EDM_DRO] Bridgeport retrofit servo questions
Luke1027
2005-01-29 10:32:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 10:55:30 UTC
Re: Bridgeport retrofit servo questions
Les Newell
2005-01-29 11:03:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 11:10:37 UTC
Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 11:14:10 UTC
Re: Bridgeport retrofit servo questions
cnc_4_me
2005-01-29 11:17:35 UTC
Re: Bridgeport retrofit servo questions
Luke1027
2005-01-29 11:22:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 11:27:02 UTC
Re: Bridgeport retrofit servo questions
cnc_4_me
2005-01-29 11:33:38 UTC
Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 11:39:04 UTC
Re: Bridgeport retrofit servo questions
washcomp
2005-01-29 11:47:14 UTC
Re: Bridgeport retrofit servo questions
cnc_4_me
2005-01-29 11:48:20 UTC
Re: Bridgeport retrofit servo questions
Luke1027
2005-01-29 11:54:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 11:55:42 UTC
Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 11:57:29 UTC
Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 12:01:44 UTC
Re: Bridgeport retrofit servo questions
cnc_4_me
2005-01-29 12:01:46 UTC
Re: Bridgeport retrofit servo questions
cnc_4_me
2005-01-29 12:06:34 UTC
Re: Bridgeport retrofit servo questions
Luke1027
2005-01-29 12:08:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
cnc_4_me
2005-01-29 12:11:35 UTC
Re: Bridgeport retrofit servo questions
cnc_4_me
2005-01-29 12:16:04 UTC
Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 12:17:27 UTC
Re: Bridgeport retrofit servo questions
cnc_4_me
2005-01-29 12:33:35 UTC
Re: Bridgeport retrofit servo questions
Luke1027
2005-01-29 12:50:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 12:52:13 UTC
Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 12:54:59 UTC
Re: Bridgeport retrofit servo questions
Les Newell
2005-01-29 13:16:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
Les Newell
2005-01-29 13:17:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
Les Newell
2005-01-29 13:25:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
R Rogers
2005-01-29 13:27:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions 1:1 ratio
braidmeister
2005-01-29 13:44:26 UTC
Re: Bridgeport retrofit servo questions 1:1 ratio
R Rogers
2005-01-29 14:24:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions 1:1 ratio
braidmeister
2005-01-29 14:45:15 UTC
Re: Bridgeport retrofit servo questions 1:1 ratio
Dan Mauch
2005-01-29 14:53:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
R Rogers
2005-01-29 15:03:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions 1:1 ratio
braidmeister
2005-01-29 15:16:26 UTC
Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 15:16:41 UTC
Re: Bridgeport retrofit servo questions 1:1 ratio
braidmeister
2005-01-29 15:43:11 UTC
Re: Bridgeport retrofit servo questions
cnc_4_me
2005-01-29 15:43:14 UTC
Re: Bridgeport retrofit servo questions
R Rogers
2005-01-29 16:02:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions 1:1 ratio
braidmeister
2005-01-29 16:03:38 UTC
Re: Bridgeport retrofit servo questions
R Rogers
2005-01-29 16:12:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
cnc_4_me
2005-01-29 16:28:32 UTC
Re: Bridgeport retrofit servo questions 1:1 ratio
cnc_4_me
2005-01-29 16:37:44 UTC
Re: Bridgeport retrofit servo questions
Luke1027
2005-01-29 16:58:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
braidmeister
2005-01-29 17:19:43 UTC
Re: Bridgeport retrofit servo questions
Luke1027
2005-01-29 17:38:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
R Rogers
2005-01-29 18:37:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions 1:1 ratio
braidmeister
2005-01-29 18:45:12 UTC
Re: Bridgeport retrofit servo questions
cnc_4_me
2005-01-29 19:31:14 UTC
Re: Bridgeport retrofit servo questions 1:1 ratio
R Rogers
2005-01-29 20:11:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions 1:1 ratio
cnc_4_me
2005-01-29 20:18:25 UTC
Re: Bridgeport retrofit servo questions 1:1 ratio
R Rogers
2005-01-29 20:42:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions 1:1 ratio
R Rogers
2005-01-29 20:47:01 UTC
CNC wiring PDF updated
cnc_4_me
2005-01-29 21:53:21 UTC
Re: CNC wiring PDF updated
Les Newell
2005-01-30 01:27:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
Polaraligned
2005-01-30 06:52:44 UTC
Re: CNC wiring PDF updated
Robert Campbell
2005-01-30 07:14:22 UTC
Re: [CAD_CAM_EDM_DRO] CNC wiring PDF updated
R Rogers
2005-01-30 08:27:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC wiring PDF updated
Dan Mauch
2005-01-30 09:48:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
Luke1027
2005-01-30 10:36:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC wiring PDF updated
braidmeister
2005-01-30 12:09:41 UTC
Re: CNC wiring PDF updated
John Stevenson
2005-01-30 15:22:13 UTC
Re: CNC wiring PDF updated
R Rogers
2005-01-30 16:41:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC wiring PDF updated
Jon Elson
2005-01-30 17:00:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
Stephen Wille Padnos
2005-01-30 18:50:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
braidmeister
2005-01-30 19:18:25 UTC
Re: Bridgeport retrofit servo questions
Dan Mauch
2005-01-31 09:29:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
Jon Elson
2005-01-31 10:17:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
Stephen Wille Padnos
2005-01-31 10:23:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
John Rouche
2005-01-31 10:36:10 UTC
Re: Bridgeport retrofit servo questions
Jon Elson
2005-01-31 23:01:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport retrofit servo questions
m0nkey0ne
2005-02-02 14:23:04 UTC
Re: Bridgeport retrofit servo questions