CAD CAM EDM DRO - Yahoo Group Archive

Re: Power supply for Servos

Posted by cnc_4_me
on 2005-02-17 18:41:17 UTC
>I'm building another control and I'm going to use a 1000va at 62
volts. The DC will be >88 volts and the Geckos should handle it.
Marris said they actually come apart at 118 >volts and 30 amps
>
> Ron


Stop the presses. Be careful there. Yes Mariss did say the drives
will come apart at 118 volts. But he didn't mean they could run
there. Fact is, most of the high voltage components in gecko drives
are rated for 100Vdc. The caps, and fets are 100Vdc parts.

Wally





--- In CAD_CAM_EDM_DRO@yahoogroups.com, R Rogers <rogersmach@y...>
wrote:
> Dave, To give you a rough idea on servo power supplies. I'm using a
800vA at 46 volts and around 16 amps for 3-13 amp continuous servos.
64 volts DC after being rectified. I get rapids on X and Y of 120
ipm. Would go faster with higher voltage. Current mostly affects
acceleration which with the supply I'm using is more than adequate. A
750 -1.5 Kva power supply would be adequate for your motors. I'm
building another control and I'm going to use a 1000va at 62 volts.
The DC will be 88 volts and the Geckos should handle it. Marris said
they actually come apart at 118 volts and 30 amps
>
> Ron
>
> turbulatordude <dave_mucha@y...> wrote:
>
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "cnc_4_me"
> wrote:
> >
> > These servo suppplys are a little hard to nail down. A couple of
> > weeks ago i tried to get a formula for making one. Both Mariss
and
> > Jon Elson gave me advice for building a supply. If i understood
> > them. The straight forward approach means you need the wattage
> > rating of the servo. Second best is the constant current spec and
> > maybe Ke constant. Third worst is the voltage and current rating
> like
> > you gave.
> >
> > Do you have any other specs on your motors...
>
>
> PACIFIC SCIENTIFIC, Permanent magnet DC motor.
> 1 1/2 hp
> 110 VDC
> 11.6 Amps
> 3,200 RPM
> Continous Duty
>
>
> If I look at the wattage of the servo, 110VDC @ 11.6 amps, that is
> 1,276 watts.
>
> But, if I look at it with the max voltage from my power supply, it
is
> 76 volts time 11.6 amps = 881 watts.
>
> For 881, I could use 2 transformers to get 2,000 watts, that is
light
> for one calculation, and heavy for the other.
>
> I had thought there was some number one could use for duty cycle as
> the motors are not driven DC, but pulsed.....
>
> I'll go back and re-read Jon's post. IIRC, it was more guidelinesh
> than calculations.
>
> Dave
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@a...,
timg@k...
> Moderator: pentam@c... indigo_red@q... davemucha@j... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach
it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be
a sister site to the CCED group, as many of the same members are
there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
>
> [Non-text portions of this message have been removed]

Discussion Thread

turbulatordude 2005-02-17 13:28:11 UTC Power supply for Servos cnc_4_me 2005-02-17 15:07:05 UTC Re: Power supply for Servos Lance Hopper 2005-02-17 15:44:55 UTC Re: Power supply for Servos turbulatordude 2005-02-17 16:39:00 UTC Re: Power supply for Servos R Rogers 2005-02-17 17:37:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos braidmeister 2005-02-17 18:04:35 UTC Re: Power supply for Servos cnc_4_me 2005-02-17 18:22:47 UTC Re: Power supply for Servos turbulatordude 2005-02-17 18:37:23 UTC Re: Power supply for Servos - bridge and caps cnc_4_me 2005-02-17 18:41:17 UTC Re: Power supply for Servos braidmeister 2005-02-17 18:48:22 UTC Re: Power supply for Servos - bridge and caps turbulatordude 2005-02-17 19:09:13 UTC Re: Power supply for Servos cnc_4_me 2005-02-17 19:26:48 UTC Re: Power supply for Servos turbulatordude 2005-02-17 19:48:10 UTC Re: Power supply for Servos - Energy dump and such Stephen Wille Padnos 2005-02-17 20:02:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-17 20:05:10 UTC Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-17 20:24:55 UTC Re: Power supply for Servos - Energy dump and such Polaraligned 2005-02-18 04:34:40 UTC Re: Power supply for Servos - bridge and caps R Rogers 2005-02-18 04:53:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - bridge and caps R Rogers 2005-02-18 05:03:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such braidmeister 2005-02-18 08:04:16 UTC Re: Power supply for Servos - bridge and caps Roy J. Tellason 2005-02-18 08:17:01 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - bridge and caps sciciora 2005-02-18 08:46:12 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps turbulatordude 2005-02-18 09:19:32 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps cnc_4_me 2005-02-18 11:33:26 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-18 11:44:27 UTC Re: Power supply for Servos - bridge and caps cnc_4_me 2005-02-18 11:50:51 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps cnc_4_me 2005-02-18 11:55:24 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps turbulatordude 2005-02-18 14:23:58 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps Polaraligned 2005-02-18 14:25:43 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-18 14:59:39 UTC Re: Power supply for Servos - Energy dump and such JanRwl@A... 2005-02-18 17:35:02 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - bridge and caps turbulatordude 2005-02-18 18:51:44 UTC Re: Power supply for Servos - Energy dump and such Dan Mauch 2005-02-19 07:29:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 07:52:11 UTC Re: Power supply for Servos - Energy dump and such Steve Stallings 2005-02-19 10:06:50 UTC Re: Power supply for Servos - Energy dump and such - URL problems turbulatordude 2005-02-19 11:57:56 UTC Re: Power supply for Servos - Energy dump and such - URL problems cnc_4_me 2005-02-19 13:32:01 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-19 13:55:03 UTC Re: Power supply for Servos - Energy dump and such - URL problems turbulatordude 2005-02-19 15:38:19 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-19 16:09:41 UTC Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 20:13:20 UTC Re: Power supply for Servos - Energy dump and such wanliker@a... 2005-02-19 20:29:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 20:54:48 UTC Re: Power supply for Servos - Energy dump and such wanliker@a... 2005-02-19 21:19:55 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-19 21:25:43 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-19 22:10:29 UTC Re: Power supply for Servos - Energy dump and such JanRwl@A... 2005-02-19 22:56:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 23:05:57 UTC Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 23:25:22 UTC Re: Power supply for Servos - Energy dump and such David Speck 2005-02-19 23:34:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-20 00:01:36 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-20 00:03:53 UTC Re: Power supply for Servos - Energy dump and such JCullins 2005-02-20 04:51:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such Lance Hopper 2005-02-20 09:33:32 UTC Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-20 09:47:29 UTC Re: Power supply for Servos - Light Bulbs turbulatordude 2005-02-20 10:17:44 UTC Re: Power supply for Servos - dump speed Stephen Wille Padnos 2005-02-20 12:44:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-20 16:13:53 UTC Re: Power supply for Servos - dump speed turbulatordude 2005-02-20 20:18:55 UTC Re: Power supply for Servos - dump speed turbulatordude 2005-02-20 20:37:39 UTC Re: Power supply for Servos - Sizign the resistor Jon Elson 2005-02-20 21:09:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Sizign the resistor