CAD CAM EDM DRO - Yahoo Group Archive

Re: Power supply for Servos - Energy dump and such

Posted by cnc_4_me
on 2005-02-19 13:32:01 UTC
I never had the link...The explanation i posted was posted in same
folder as the PDF...BTW as of yesterday i think a new updated pdf was
put in files section on gecko site, i think in G201 folder...It
dosn't say anything else than what i posted though...

Wally


--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Dan Mauch" <dmauch@s...>
wrote:
> Ah-Ha that explains why the power dump circuit that I made from
Mariss's
> schematic didn't work. I didn't have time to go back and try to
figure out
> what was wrong but that would certainly explain it.
> Can you provide a link to the message number that explains the
details?
> Dan
> ----- Original Message -----
> From: "cnc_4_me" <cnc4me@g...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Friday, February 18, 2005 2:59 PM
> Subject: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy
dump and
> such
>
>
> >
> >
> > here is the url and the correction for a component.
> >
> >
> >
http://f6.grp.yahoofs.com/v1/YGUWQgywUky_ZHvbcMT_VezYgefaipzww5J7R_nII
> > Zzg9Ii_E73bxbkclsxk_ubuLEBeSgwQB5hU8KNmRe7q_Qe0AhD4pg/G320%20and%
> > 20G340/POWER%20SUPPLY.pdf
> >
> >
> > "The Power Supply circuit created by Mariss June 16, 2002, calls
for
> > an 1N752 for
> > D5. The 1N752 provides 5.6 volts, not the 12 volts which the
circuit
> > indicates. I
> > found the circuit did not work with a 5.6 volt zener, and did work
> > with a 12 volt
> > zener, such as the 1N759A or the 1N5242B (I used the latter).
> >
> > There was lengthy discussion of this as I debugged my PCB and for
> > anyone who needs
> > to know they can find it on the list. (Heads much wiser than mine
> > advised the
> > change was appropriate.)
> >
> > Grant Fair"
> >
> >
> > Wally
> >
> >
> >
> > --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Polaraligned"
> > <polaraligned@o...> wrote:
> >>
> >> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "cnc_4_me" <cnc4me@g...>
> >> wrote:
> >> >
> >> > With 88V you should be using one of the energy dump circuits
> > Mariss
> >> > published.
> >> >
> >> > Wally
> >>
> >>
> >> Where do I find info on this circuit Wally?
> >>
> >> Thanks,
> >> Scott
> >
> >
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
wanliker@a...,
> > timg@k...
> > Moderator: pentam@c... indigo_red@q... davemucha@j...
> > [Moderators]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
reach it
> > if you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this
to be a
> > sister site to the CCED group, as many of the same members are
there, for
> > OT subjects, that are not allowed on the CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
POSTING THEM.
> > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
> >
> >
> >

Discussion Thread

turbulatordude 2005-02-17 13:28:11 UTC Power supply for Servos cnc_4_me 2005-02-17 15:07:05 UTC Re: Power supply for Servos Lance Hopper 2005-02-17 15:44:55 UTC Re: Power supply for Servos turbulatordude 2005-02-17 16:39:00 UTC Re: Power supply for Servos R Rogers 2005-02-17 17:37:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos braidmeister 2005-02-17 18:04:35 UTC Re: Power supply for Servos cnc_4_me 2005-02-17 18:22:47 UTC Re: Power supply for Servos turbulatordude 2005-02-17 18:37:23 UTC Re: Power supply for Servos - bridge and caps cnc_4_me 2005-02-17 18:41:17 UTC Re: Power supply for Servos braidmeister 2005-02-17 18:48:22 UTC Re: Power supply for Servos - bridge and caps turbulatordude 2005-02-17 19:09:13 UTC Re: Power supply for Servos cnc_4_me 2005-02-17 19:26:48 UTC Re: Power supply for Servos turbulatordude 2005-02-17 19:48:10 UTC Re: Power supply for Servos - Energy dump and such Stephen Wille Padnos 2005-02-17 20:02:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-17 20:05:10 UTC Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-17 20:24:55 UTC Re: Power supply for Servos - Energy dump and such Polaraligned 2005-02-18 04:34:40 UTC Re: Power supply for Servos - bridge and caps R Rogers 2005-02-18 04:53:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - bridge and caps R Rogers 2005-02-18 05:03:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such braidmeister 2005-02-18 08:04:16 UTC Re: Power supply for Servos - bridge and caps Roy J. Tellason 2005-02-18 08:17:01 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - bridge and caps sciciora 2005-02-18 08:46:12 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps turbulatordude 2005-02-18 09:19:32 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps cnc_4_me 2005-02-18 11:33:26 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-18 11:44:27 UTC Re: Power supply for Servos - bridge and caps cnc_4_me 2005-02-18 11:50:51 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps cnc_4_me 2005-02-18 11:55:24 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps turbulatordude 2005-02-18 14:23:58 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps Polaraligned 2005-02-18 14:25:43 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-18 14:59:39 UTC Re: Power supply for Servos - Energy dump and such JanRwl@A... 2005-02-18 17:35:02 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - bridge and caps turbulatordude 2005-02-18 18:51:44 UTC Re: Power supply for Servos - Energy dump and such Dan Mauch 2005-02-19 07:29:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 07:52:11 UTC Re: Power supply for Servos - Energy dump and such Steve Stallings 2005-02-19 10:06:50 UTC Re: Power supply for Servos - Energy dump and such - URL problems turbulatordude 2005-02-19 11:57:56 UTC Re: Power supply for Servos - Energy dump and such - URL problems cnc_4_me 2005-02-19 13:32:01 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-19 13:55:03 UTC Re: Power supply for Servos - Energy dump and such - URL problems turbulatordude 2005-02-19 15:38:19 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-19 16:09:41 UTC Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 20:13:20 UTC Re: Power supply for Servos - Energy dump and such wanliker@a... 2005-02-19 20:29:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 20:54:48 UTC Re: Power supply for Servos - Energy dump and such wanliker@a... 2005-02-19 21:19:55 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-19 21:25:43 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-19 22:10:29 UTC Re: Power supply for Servos - Energy dump and such JanRwl@A... 2005-02-19 22:56:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 23:05:57 UTC Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 23:25:22 UTC Re: Power supply for Servos - Energy dump and such David Speck 2005-02-19 23:34:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-20 00:01:36 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-20 00:03:53 UTC Re: Power supply for Servos - Energy dump and such JCullins 2005-02-20 04:51:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such Lance Hopper 2005-02-20 09:33:32 UTC Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-20 09:47:29 UTC Re: Power supply for Servos - Light Bulbs turbulatordude 2005-02-20 10:17:44 UTC Re: Power supply for Servos - dump speed Stephen Wille Padnos 2005-02-20 12:44:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-20 16:13:53 UTC Re: Power supply for Servos - dump speed turbulatordude 2005-02-20 20:18:55 UTC Re: Power supply for Servos - dump speed turbulatordude 2005-02-20 20:37:39 UTC Re: Power supply for Servos - Sizign the resistor Jon Elson 2005-02-20 21:09:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Sizign the resistor