CAD CAM EDM DRO - Yahoo Group Archive

Re: Power supply for Servos - dump speed

on 2005-02-20 10:17:44 UTC
> gecko group, files, g201, returned energy.pdf Read it carefully
the
> second graph applies. It shows it takes .8 seconds for power to
> return to normal in a torture test.
>
> Wally

I'm not sure if I follow the picture.

The peaks show rectified AC, so there would be 120 peaks per second.
Less than half of each peak has a voltage rise,

The DC bus shows the voltage rise of the power supply and in the back
EMF mode, it shows the DC voltage rising to be above the desired
threshold.

So, there are 240 intersections, 120 where it rises above the
threshold, and 120 where it drops below.

since it appears that just under half of the time, the voltage is
above the threshold, we can determine that 1 second divided by 120
peaks is 0.008333. Therefore each rise would occur every 0.008333
seconds and last for half of that.

The rise above the line shows the rise, but it does not show at what
point the comparitor circuit engages. It does show the dump to be
very abrupt, at almost 1/10 of the half wave or 0.000833 seconds.

Dave

Discussion Thread

turbulatordude 2005-02-17 13:28:11 UTC Power supply for Servos cnc_4_me 2005-02-17 15:07:05 UTC Re: Power supply for Servos Lance Hopper 2005-02-17 15:44:55 UTC Re: Power supply for Servos turbulatordude 2005-02-17 16:39:00 UTC Re: Power supply for Servos R Rogers 2005-02-17 17:37:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos braidmeister 2005-02-17 18:04:35 UTC Re: Power supply for Servos cnc_4_me 2005-02-17 18:22:47 UTC Re: Power supply for Servos turbulatordude 2005-02-17 18:37:23 UTC Re: Power supply for Servos - bridge and caps cnc_4_me 2005-02-17 18:41:17 UTC Re: Power supply for Servos braidmeister 2005-02-17 18:48:22 UTC Re: Power supply for Servos - bridge and caps turbulatordude 2005-02-17 19:09:13 UTC Re: Power supply for Servos cnc_4_me 2005-02-17 19:26:48 UTC Re: Power supply for Servos turbulatordude 2005-02-17 19:48:10 UTC Re: Power supply for Servos - Energy dump and such Stephen Wille Padnos 2005-02-17 20:02:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-17 20:05:10 UTC Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-17 20:24:55 UTC Re: Power supply for Servos - Energy dump and such Polaraligned 2005-02-18 04:34:40 UTC Re: Power supply for Servos - bridge and caps R Rogers 2005-02-18 04:53:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - bridge and caps R Rogers 2005-02-18 05:03:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such braidmeister 2005-02-18 08:04:16 UTC Re: Power supply for Servos - bridge and caps Roy J. Tellason 2005-02-18 08:17:01 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - bridge and caps sciciora 2005-02-18 08:46:12 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps turbulatordude 2005-02-18 09:19:32 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps cnc_4_me 2005-02-18 11:33:26 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-18 11:44:27 UTC Re: Power supply for Servos - bridge and caps cnc_4_me 2005-02-18 11:50:51 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps cnc_4_me 2005-02-18 11:55:24 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps turbulatordude 2005-02-18 14:23:58 UTC Bridge voltage rating: Re: Power supply for Servos - bridge and caps Polaraligned 2005-02-18 14:25:43 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-18 14:59:39 UTC Re: Power supply for Servos - Energy dump and such JanRwl@A... 2005-02-18 17:35:02 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - bridge and caps turbulatordude 2005-02-18 18:51:44 UTC Re: Power supply for Servos - Energy dump and such Dan Mauch 2005-02-19 07:29:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 07:52:11 UTC Re: Power supply for Servos - Energy dump and such Steve Stallings 2005-02-19 10:06:50 UTC Re: Power supply for Servos - Energy dump and such - URL problems turbulatordude 2005-02-19 11:57:56 UTC Re: Power supply for Servos - Energy dump and such - URL problems cnc_4_me 2005-02-19 13:32:01 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-19 13:55:03 UTC Re: Power supply for Servos - Energy dump and such - URL problems turbulatordude 2005-02-19 15:38:19 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-19 16:09:41 UTC Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 20:13:20 UTC Re: Power supply for Servos - Energy dump and such wanliker@a... 2005-02-19 20:29:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 20:54:48 UTC Re: Power supply for Servos - Energy dump and such wanliker@a... 2005-02-19 21:19:55 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-19 21:25:43 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-19 22:10:29 UTC Re: Power supply for Servos - Energy dump and such JanRwl@A... 2005-02-19 22:56:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 23:05:57 UTC Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-19 23:25:22 UTC Re: Power supply for Servos - Energy dump and such David Speck 2005-02-19 23:34:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-20 00:01:36 UTC Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-20 00:03:53 UTC Re: Power supply for Servos - Energy dump and such JCullins 2005-02-20 04:51:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such Lance Hopper 2005-02-20 09:33:32 UTC Re: Power supply for Servos - Energy dump and such turbulatordude 2005-02-20 09:47:29 UTC Re: Power supply for Servos - Light Bulbs turbulatordude 2005-02-20 10:17:44 UTC Re: Power supply for Servos - dump speed Stephen Wille Padnos 2005-02-20 12:44:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Energy dump and such cnc_4_me 2005-02-20 16:13:53 UTC Re: Power supply for Servos - dump speed turbulatordude 2005-02-20 20:18:55 UTC Re: Power supply for Servos - dump speed turbulatordude 2005-02-20 20:37:39 UTC Re: Power supply for Servos - Sizign the resistor Jon Elson 2005-02-20 21:09:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supply for Servos - Sizign the resistor