CAD CAM EDM DRO - Yahoo Group Archive

Re: Servo drives- Mariss

Posted by Polaraligned
on 2005-05-13 03:14:48 UTC
Well, the question really is are you going to do for your servo drives
what you have done for your stepper drives? A lot of servo fans here
as you can see.

Thanks,
Scott





--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Mariss Freimanis"
<mariss92705@y...> wrote:
> Scott,
>
> Well, it's hard to compete against something no one has seen yet. :-)
> Rutex builds very nice drives though from what I hear.
>
> We have been busy too. We will be launching 5 new products over the
> next 30 days:
>
> 1) G202: Like a G201 but needs no heatsink or 470uF/100V cap and has
> short-circuit protection and power-on reset. May 25.
>
> 2) G212: Like a G210 with the features of (1).
>
> 3) G100: The G2002 motion controller is renamed. 6 axies of
> step/direction (4MHz), 6 axies of quadrature encoder inputs including
> index (1MHz), 22 general-purpose filtered and protected inputs, 16
> general-purpose 100mA, 24VDC relay-rated outputs, 4 digital to analog 0-
> 5V outputs, 4 analog to digital 0-5V inputs, USB and/or ethernet ports,
> 96 position terminal blocks, 70 LED I/O indicators, anodised enclosure,
> 2.5" W by 7.5" L by 1.5" H, etc.
>
> 4) G101: Same as (3) but no enclosure, terminal blocks or LEDs. IDE
> cable headers for all I/O, 2" by 4.5" board, under $200.
>
> 5) G204V: The vampire drive. Every protection circuit, low motor
> dissipation.
>
> Other, more exciting things are in the works for later.
>
> About our numbering system:
>
> G100-series: Motion controllers
> G200-series: Step motor drives
> G300-series: DC brush-type servo drives
> G400-series: 3-phase brushless servo drives
> G500 thru G800-series: TBD
> G900-series: Miscellaneous products
>
> Mariss
>
>
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Polaraligned"
> <polaraligned@o...> wrote:
> > Mariss, do you have plans for a drive to compete head to head
> > with the soon to be released Rutex R2000 servo drive? If so, what
> > is the time frame?
> >
> > Thanks,
> > Scott

Discussion Thread

Pete Brown (YahooGroups) 2005-05-06 06:22:54 UTC What makes a motor a servo? turbulatordude 2005-05-06 07:23:06 UTC Re: What makes a motor a servo? Jon Elson 2005-05-06 08:19:45 UTC Re: [CAD_CAM_EDM_DRO] What makes a motor a servo? Pete Brown (YahooGroups) 2005-05-06 09:29:24 UTC RE: [CAD_CAM_EDM_DRO] What makes a motor a servo? Alex Holden 2005-05-06 10:32:26 UTC Re: [CAD_CAM_EDM_DRO] What makes a motor a servo? Les Newell 2005-05-06 11:27:14 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? Pete Brown (YahooGroups) 2005-05-06 12:30:42 UTC RE: [CAD_CAM_EDM_DRO] What makes a motor a servo? cnc_4_me 2005-05-06 12:33:28 UTC Re: What makes a motor a servo? Alex Holden 2005-05-06 12:48:41 UTC Re: [CAD_CAM_EDM_DRO] What makes a motor a servo? cnc002@a... 2005-05-06 13:25:14 UTC Re: [CAD_CAM_EDM_DRO] What makes a motor a servo? Codesuidae 2005-05-06 13:38:31 UTC Re: [CAD_CAM_EDM_DRO] What makes a motor a servo? Jon Elson 2005-05-06 18:56:30 UTC Re: [CAD_CAM_EDM_DRO] What makes a motor a servo? turbulatordude 2005-05-06 21:25:53 UTC Re: What makes a motor a servo? treadmill cnc_4_me 2005-05-06 21:39:03 UTC Re: What makes a motor a servo? cnc_4_me 2005-05-06 21:54:02 UTC Re: What makes a motor a servo? treadmill turbulatordude 2005-05-06 22:28:08 UTC Re: What makes a motor a servo? 80% of rated speed ? cnc_4_me 2005-05-06 22:34:45 UTC Re: What makes a motor a servo? 80% of rated speed ? vrsculptor 2005-05-07 09:34:49 UTC Re: What makes a motor a servo? treadmill 1.5 volt turbulatordude 2005-05-07 10:02:18 UTC Re: What makes a motor a servo? treadmill 1.5 volt Mariss Freimanis 2005-05-07 12:00:35 UTC Re: What makes a motor a servo? Jon Elson 2005-05-07 12:56:21 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? treadmill Jon Elson 2005-05-07 13:08:50 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? 80% of rated speed ? Jon Elson 2005-05-07 13:28:52 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? Jon Elson 2005-05-07 13:40:11 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? Mariss Freimanis 2005-05-07 14:46:53 UTC Re: What makes a motor a servo? Polaraligned 2005-05-07 15:07:09 UTC Re: What makes a motor a servo? Mariss Freimanis 2005-05-07 15:44:04 UTC Re: What makes a motor a servo? Ron Kline 2005-05-07 16:45:05 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? R Rogers 2005-05-07 18:00:17 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? cnc_4_me 2005-05-07 18:04:15 UTC Re: What makes a motor a servo? cnc_4_me 2005-05-07 18:16:56 UTC Re: What makes a motor a servo? Polaraligned 2005-05-07 18:37:20 UTC Re: What makes a motor a servo? Polaraligned 2005-05-07 18:44:10 UTC Re: What makes a motor a servo? JanRwl@A... 2005-05-07 19:38:02 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? cnc_4_me 2005-05-07 19:47:49 UTC Re: What makes a motor a servo? Mariss Freimanis 2005-05-07 20:12:18 UTC Re: What makes a motor a servo? JanRwl@A... 2005-05-07 20:23:13 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? Jon Elson 2005-05-07 21:29:37 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? Jon Elson 2005-05-07 21:36:40 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? Mariss Freimanis 2005-05-07 22:06:51 UTC Re: What makes a motor a servo? David Bloomfield 2005-05-08 05:46:29 UTC Re: What makes a motor a servo? turbulatordude 2005-05-08 05:57:41 UTC Re: What makes a motor a servo? Ed Fanta 2005-05-08 06:29:20 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? lcdpublishing 2005-05-08 09:27:46 UTC Re: What makes a motor a servo? Polaraligned 2005-05-08 10:08:45 UTC Re: What makes a motor a servo? Polaraligned 2005-05-08 10:17:29 UTC Re: What makes a motor a servo? Jon Elson 2005-05-08 11:17:44 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? cnc_4_me 2005-05-08 11:35:12 UTC Re: What makes a motor a servo? lcdpublishing 2005-05-08 11:54:09 UTC Re: What makes a motor a servo? cnc_4_me 2005-05-08 12:12:49 UTC Re: What makes a motor a servo? Polaraligned 2005-05-08 12:20:54 UTC Re: What makes a motor a servo? Polaraligned 2005-05-08 12:34:55 UTC Re: What makes a motor a servo? Polaraligned 2005-05-08 12:41:01 UTC Re: What makes a motor a servo? Mariss Freimanis 2005-05-08 12:42:04 UTC Re: What makes a motor a servo? turbulatordude 2005-05-08 15:35:11 UTC Re: What makes a motor a servo? - real world applications bobmcknight@c... 2005-05-09 23:37:05 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? turbulatordude 2005-05-10 07:18:49 UTC Re: What makes a motor a servo? calculating power turbulatordude 2005-05-10 07:29:46 UTC Re: What makes a motor a servo? Polaraligned 2005-05-10 11:40:29 UTC Re: What makes a motor a servo? Polaraligned 2005-05-10 13:23:51 UTC Re: What makes a motor a servo? John Meissner 2005-05-10 14:21:37 UTC Re: What makes a motor a servo? John Meissner 2005-05-10 15:20:32 UTC Re: What makes a motor a servo? Polaraligned 2005-05-10 17:55:10 UTC Re: What makes a motor a servo? calculating power Erie Patsellis 2005-05-10 19:17:15 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power R Rogers 2005-05-10 20:23:24 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power turbulatordude 2005-05-10 20:25:11 UTC Re: What makes a motor a servo? calculating power Mariss Freimanis 2005-05-10 21:11:37 UTC Re: What makes a motor a servo? calculating power Mariss Freimanis 2005-05-10 21:22:03 UTC Re: What makes a motor a servo? calculating power Erie Patsellis 2005-05-10 21:27:29 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power turbulatordude 2005-05-10 23:44:45 UTC Re: What makes a motor a servo? calculating power Alex Holden 2005-05-11 01:00:09 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power Les Newell 2005-05-11 02:40:25 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power lcdpublishing 2005-05-11 04:44:17 UTC Re: What makes a motor a servo? calculating power Les Newell 2005-05-11 05:52:52 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power turbulatordude 2005-05-11 07:02:58 UTC Re: What makes a motor a servo? gearing servos Alex Holden 2005-05-11 07:20:53 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? gearing servos turbulatordude 2005-05-11 08:09:09 UTC Re: What makes a motor a servo? gearing servos Alan Marconett 2005-05-11 08:27:18 UTC RE: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power lcdpublishing 2005-05-11 08:53:35 UTC Re: What makes a motor a servo? calculating power Mariss Freimanis 2005-05-11 10:01:27 UTC Re: What makes a motor a servo? calculating power bobmcknight@c... 2005-05-11 10:45:16 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power Codesuidae 2005-05-11 10:53:27 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power Mariss Freimanis 2005-05-11 11:06:53 UTC Re: What makes a motor a servo? calculating power Alan Marconett 2005-05-11 11:49:12 UTC RE: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power Alan Marconett 2005-05-11 11:57:39 UTC RE: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power Mariss Freimanis 2005-05-11 11:59:45 UTC Re: What makes a motor a servo? calculating power Mariss Freimanis 2005-05-11 12:10:00 UTC Re: What makes a motor a servo? calculating power Codesuidae 2005-05-11 12:29:35 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power Hugh Prescott 2005-05-11 12:59:24 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power bobmcknight@c... 2005-05-11 13:08:51 UTC RE: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power bobmcknight@c... 2005-05-11 13:09:16 UTC RE: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power Luke1027 2005-05-11 14:00:18 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power turbulatordude 2005-05-11 15:05:43 UTC Re: What makes a motor a servo? calculating power Alan Marconett 2005-05-11 16:15:59 UTC RE: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power Jon Elson 2005-05-11 19:26:23 UTC Re: [CAD_CAM_EDM_DRO] Re: What makes a motor a servo? calculating power David Bloomfield 2005-05-11 20:21:19 UTC Re: What makes a motor a servo? calculating power Polaraligned 2005-05-12 03:05:43 UTC Servo drives- Mariss turbulatordude 2005-05-12 07:54:41 UTC Re: Servo drives- Mariss Adrian Kole 2005-05-12 08:13:30 UTC Re: Servo drives- Mariss Codesuidae 2005-05-12 08:16:40 UTC Re: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss Mariss Freimanis 2005-05-12 08:30:36 UTC Re: Servo drives- Mariss R Rogers 2005-05-12 08:32:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss Alan Marconett 2005-05-12 08:37:39 UTC RE: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss JCullins 2005-05-12 08:50:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss Jon Elson 2005-05-12 09:28:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss Leslie Watts 2005-05-12 09:52:21 UTC RE: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss Mariss Freimanis 2005-05-12 10:00:50 UTC Re: Servo drives- Mariss Mariss Freimanis 2005-05-12 10:22:31 UTC Re: Servo drives- Mariss Codesuidae 2005-05-12 10:33:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss Les Newell 2005-05-12 11:16:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss turbulatordude 2005-05-12 12:01:55 UTC Re: Servo drives- Mariss Mariss Freimanis 2005-05-12 12:14:08 UTC Re: Servo drives- Mariss Leslie Watts 2005-05-12 13:08:30 UTC RE: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss cnc_4_me 2005-05-12 13:10:08 UTC Re: Servo drives- Mariss David A. Frantz 2005-05-12 15:04:01 UTC Re: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss JCullins 2005-05-12 15:08:43 UTC Re: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss Mariss Freimanis 2005-05-12 16:18:53 UTC Re: Servo drives- Mariss JCullins 2005-05-12 16:41:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss turbulatordude 2005-05-12 19:35:25 UTC Re: Servo drives- exploding head Erie Patsellis 2005-05-12 20:11:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Servo drives- exploding head cnc_4_me 2005-05-12 20:28:03 UTC Re: Servo drives- exploding head Polaraligned 2005-05-13 03:10:01 UTC Re: Servo drives- Mariss Polaraligned 2005-05-13 03:14:48 UTC Re: Servo drives- Mariss turbulatordude 2005-05-13 08:00:30 UTC Re: Servo drives- Mariss Leslie Watts 2005-05-13 08:15:28 UTC RE: [CAD_CAM_EDM_DRO] Re: Servo drives- exploding head cnc_4_me 2005-05-13 08:27:58 UTC Re: Servo drives- exploding head m0nkey0ne 2005-05-13 08:53:54 UTC Re: Servo drives- exploding head prevention Dave Shiels 2005-05-13 14:55:00 UTC Re: [CAD_CAM_EDM_DRO] Re: Servo drives- exploding head turbulatordude 2005-05-14 08:26:04 UTC Re: Servo drives- exploding head caudlet 2005-05-14 09:01:51 UTC Re: Servo drives- exploding head Leslie Watts 2005-05-14 10:21:56 UTC RE: [CAD_CAM_EDM_DRO] Re: Servo drives- exploding head turbulatordude 2005-05-14 10:53:16 UTC Re: Servo drives- exploding head turbulatordude 2005-05-14 12:42:47 UTC Re: Servo drives- exploding head - Router/plasma Erie Patsellis 2005-05-14 15:45:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Servo drives- exploding head - Router/plasma turbulatordude 2005-05-14 18:37:57 UTC Re: Servo drives- exploding head - Router/plasma Dave Fisher 2005-05-23 16:05:06 UTC RE: [CAD_CAM_EDM_DRO] Re:NEMA 23 Stepper Motors