Re: [CAD_CAM_EDM_DRO] Encoder question
Posted by
Dan Mauch
on 2006-03-08 17:40:31 UTC
First you should check to see what the current drain is for that encoder.
The G320/340 can only supply 50 ma. Many encoders typically draw 75-125MA.
You can still use them but you would need an external 5V power supply
capable of handling the current for all the servo motors equiped with those
encoders. Then don't forget to add the 470 ohm resistor between the G320
Enc+ and enc - terminals.
But from your post you are asking for a a step/direction brushless. servo
amp. Brushless servo motors wouldn't work with the G320/G340's
Dan Mauch
low cost stepper and servo motors.
cases for Gecko drives
kits and assembled 3-4 axis drives
www.camtronics-cnc.com
www.seanet.com/~dmauch
The G320/340 can only supply 50 ma. Many encoders typically draw 75-125MA.
You can still use them but you would need an external 5V power supply
capable of handling the current for all the servo motors equiped with those
encoders. Then don't forget to add the 470 ohm resistor between the G320
Enc+ and enc - terminals.
But from your post you are asking for a a step/direction brushless. servo
amp. Brushless servo motors wouldn't work with the G320/G340's
Dan Mauch
low cost stepper and servo motors.
cases for Gecko drives
kits and assembled 3-4 axis drives
www.camtronics-cnc.com
www.seanet.com/~dmauch
----- Original Message -----
From: "BRIAN FOLEY" <ka1bbg@...>
To: <Cad_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, March 08, 2006 2:42 PM
Subject: [CAD_CAM_EDM_DRO] Encoder question
> Hi, bought some servo motors with "Qeds" encoders, problem is they are not
> Qeds but Dunkermotoren RE30-2-500+t15v........
> these are 5 volt, incremental square wave 500 pulse per rev with a,b,/a,/b
> quadrature outputs. can i use these for encoder for say a Gecko drive
> using just a,b outputs?
> Any one have a step/direction brushless servo drives for up to 5 amps i
> might be interested.
> thanks, brian f.
>
>
Discussion Thread
Robert
2000-06-13 16:10:41 UTC
Encoder question
F. de Beer
2001-07-21 11:33:47 UTC
Re: [CAD_CAM_EDM_DRO] Encoder question
Jon Elson
2001-07-21 15:47:57 UTC
Re: [CAD_CAM_EDM_DRO] Encoder question
Scott M. Thomas
2001-07-23 09:56:48 UTC
RE: [CAD_CAM_EDM_DRO] Encoder question
babinda01
2005-04-04 04:16:38 UTC
Encoder question
Jon Elson
2005-04-04 09:49:53 UTC
Re: [CAD_CAM_EDM_DRO] Encoder question
Roy J. Tellason
2005-04-04 10:49:17 UTC
Re: [CAD_CAM_EDM_DRO] Encoder question
Jon Elson
2005-04-04 22:47:40 UTC
Re: [CAD_CAM_EDM_DRO] Encoder question
cnc002@a...
2005-04-05 07:39:29 UTC
Re: [CAD_CAM_EDM_DRO] Encoder question
Mcginnis, Darrell S
2005-05-17 16:00:56 UTC
RE: [CAD_CAM_EDM_DRO] Encoder question
BRIAN FOLEY
2006-03-08 14:40:37 UTC
Encoder question
Dan Mauch
2006-03-08 17:40:31 UTC
Re: [CAD_CAM_EDM_DRO] Encoder question
BRIAN FOLEY
2006-03-08 22:00:27 UTC
Re: [CAD_CAM_EDM_DRO] Encoder question
Peter Homann
2006-03-08 22:06:48 UTC
Re: [CAD_CAM_EDM_DRO] Encoder question
BRIAN FOLEY
2006-03-08 23:42:13 UTC
Re: [CAD_CAM_EDM_DRO] Encoder question
Carl Mikkelsen
2006-03-10 14:12:50 UTC
Re: [CAD_CAM_EDM_DRO] Encoder question - Rutex concerns
Jon Elson
2006-03-10 18:21:53 UTC
Re: [CAD_CAM_EDM_DRO] Encoder question - Rutex concerns
John Dammeyer
2006-03-10 19:40:43 UTC
MPG behaviour
craig strudwicke
2006-03-10 21:06:52 UTC
RE: [CAD_CAM_EDM_DRO] MPG behaviour
Steve Blackmore
2006-03-11 00:44:27 UTC
Re: [CAD_CAM_EDM_DRO] MPG behaviour
Andy Wander
2006-03-11 04:08:50 UTC
RE: [CAD_CAM_EDM_DRO] MPG behaviour
Alan Marconett
2006-03-11 09:06:05 UTC
Re: [CAD_CAM_EDM_DRO] MPG behaviour
bob_kellock
2006-03-11 09:47:45 UTC
Re: Encoder question - Rutex concerns
Peter Homann
2006-03-11 14:31:49 UTC
Re: [CAD_CAM_EDM_DRO] MPG behaviour
skykotech
2006-03-14 10:54:55 UTC
Re: Encoder question
BRIAN FOLEY
2006-03-14 13:45:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Encoder question
Les Newell
2006-03-14 14:05:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Encoder question
BRIAN FOLEY
2006-03-14 14:46:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Encoder question
skykotech
2006-03-14 16:09:20 UTC
Re: Encoder question
BRIAN FOLEY
2006-03-14 16:12:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Encoder question