Re: Glass cutting
Posted by
balsanu_gabi
on 2006-10-22 07:31:59 UTC
Hi Roger,
I was wondering that diamond scriber can cut the glass until
breaking points?
TIA
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "vrsculptor"
<vrsculptor@...> wrote:
I was wondering that diamond scriber can cut the glass until
breaking points?
TIA
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "vrsculptor"
<vrsculptor@...> wrote:
>cuts in
> Sounds like a neat idea. Isn't using a wheel to scribe glass a lot
> like using a knife to cut vinyl? In both cases the cutter only
> one direction. Mach3 has the ability to turn the knife, using anaxis
> motor on the cutter shaft, in the direction of the cut. You mighttry
> searching on tangenital (sp?) cutters on the web or vinyl cuttingin
> the Mach3 group.direction.
>
> Could you use a diamond scriber instead of a wheel to do your
> scribing? I think engravers use them. It would scratch in any
>my
> Roger
>
> > I know how to cut glass, what I don't know is how to "tell" my
> > driver to move wheel glass cutter after a line. I think I need a
> > stepper motor to do that (I am very new in this area - CNC). If
> > guess is right - how I can "tell" to do that?
>
Discussion Thread
balsanu_gabi
2006-10-22 03:20:59 UTC
Glass cutting
Tony Smith
2006-10-22 05:27:50 UTC
RE: [CAD_CAM_EDM_DRO] Glass cutting
balsanu_gabi
2006-10-22 05:45:45 UTC
Re: Glass cutting
Tony Smith
2006-10-22 07:08:46 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
vrsculptor
2006-10-22 07:18:40 UTC
Re: Glass cutting
balsanu_gabi
2006-10-22 07:31:59 UTC
Re: Glass cutting
vrsculptor
2006-10-22 07:45:42 UTC
Re: Glass cutting
Tony Smith
2006-10-22 08:10:40 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Tony Smith
2006-10-22 09:05:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
vrsculptor
2006-10-22 11:04:30 UTC
Re: Glass cutting
Tony Smith
2006-10-22 11:32:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Jack Coats
2006-10-22 16:44:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Jack Coats
2006-10-22 16:54:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
Jon Elson
2006-10-22 17:49:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
jesse Brennan
2006-10-22 19:15:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
Tony Smith
2006-10-23 00:30:54 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Brad Eyben
2006-10-23 06:36:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
jesse Brennan
2006-10-23 07:04:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
optics22000
2006-10-23 10:55:40 UTC
Re: Glass cutting
Tony Smith
2006-10-23 11:16:27 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Tony Smith
2006-10-23 11:31:49 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
balsanu_gabi
2006-10-23 13:30:41 UTC
Re: Glass cutting
optics22000
2006-10-23 22:48:05 UTC
Re: Glass cutting