Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
Posted by
jesse Brennan
on 2006-10-23 07:04:08 UTC
You are right I p[aid more attention to the next paragraph-- they
are using the Tap wheel.
I have never seen glass follow a detailed line without breaking
pliers used to run the crack even then it often doesn't work .
The machine is capable of delivering 60 psi pressure, but far less is
required to accomplish up to 0.250" cuts on flat glass/substrates,
especially when using a Toyo TAP or Deep Cut carbide wheel.
. There is
That site was claiming to cut 6mm (1/4") glass on that machine. Neat
trick
if it true. Or I read it wrong :)
Tony
[Non-text portions of this message have been removed]
are using the Tap wheel.
I have never seen glass follow a detailed line without breaking
pliers used to run the crack even then it often doesn't work .
The machine is capable of delivering 60 psi pressure, but far less is
required to accomplish up to 0.250" cuts on flat glass/substrates,
especially when using a Toyo TAP or Deep Cut carbide wheel.
. There is
> an interesting technique shown where the carbide wheel axlejesse
> hole is cut with a spline or like an internal planetary gear
> to put enough vibration in to run the break. Tap wheel
That site was claiming to cut 6mm (1/4") glass on that machine. Neat
trick
if it true. Or I read it wrong :)
Tony
[Non-text portions of this message have been removed]
Discussion Thread
balsanu_gabi
2006-10-22 03:20:59 UTC
Glass cutting
Tony Smith
2006-10-22 05:27:50 UTC
RE: [CAD_CAM_EDM_DRO] Glass cutting
balsanu_gabi
2006-10-22 05:45:45 UTC
Re: Glass cutting
Tony Smith
2006-10-22 07:08:46 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
vrsculptor
2006-10-22 07:18:40 UTC
Re: Glass cutting
balsanu_gabi
2006-10-22 07:31:59 UTC
Re: Glass cutting
vrsculptor
2006-10-22 07:45:42 UTC
Re: Glass cutting
Tony Smith
2006-10-22 08:10:40 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Tony Smith
2006-10-22 09:05:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
vrsculptor
2006-10-22 11:04:30 UTC
Re: Glass cutting
Tony Smith
2006-10-22 11:32:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Jack Coats
2006-10-22 16:44:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Jack Coats
2006-10-22 16:54:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
Jon Elson
2006-10-22 17:49:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
jesse Brennan
2006-10-22 19:15:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
Tony Smith
2006-10-23 00:30:54 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Brad Eyben
2006-10-23 06:36:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
jesse Brennan
2006-10-23 07:04:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
optics22000
2006-10-23 10:55:40 UTC
Re: Glass cutting
Tony Smith
2006-10-23 11:16:27 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Tony Smith
2006-10-23 11:31:49 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
balsanu_gabi
2006-10-23 13:30:41 UTC
Re: Glass cutting
optics22000
2006-10-23 22:48:05 UTC
Re: Glass cutting