Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
Posted by
Jon Elson
on 2006-10-22 17:49:46 UTC
Jack Coats wrote:
nature. I really
don't think there is any hope of doing this, at least at normal temperature.
It might be possible to mill glass at, say, 500 F or so, where it gets a
bit soft.
I did a project for a friend that involved making Vee grooves in glass.
These were
straight grooves, so we tilted the head of the Bridgeport, and used a
diamond
wheel that we had dressed to a square edge. We had to use a LOT of water
to keep the glass from cracking, and feed at a terribly slow rate.
Something like
1 IPM.
Jon
>I know it is not the same thing, but has anyone tried 'milling' glass,The problem is the large stresses in most glass, and its brittle
>to 'mechanical etching'?
>
>
nature. I really
don't think there is any hope of doing this, at least at normal temperature.
It might be possible to mill glass at, say, 500 F or so, where it gets a
bit soft.
I did a project for a friend that involved making Vee grooves in glass.
These were
straight grooves, so we tilted the head of the Bridgeport, and used a
diamond
wheel that we had dressed to a square edge. We had to use a LOT of water
to keep the glass from cracking, and feed at a terribly slow rate.
Something like
1 IPM.
Jon
Discussion Thread
balsanu_gabi
2006-10-22 03:20:59 UTC
Glass cutting
Tony Smith
2006-10-22 05:27:50 UTC
RE: [CAD_CAM_EDM_DRO] Glass cutting
balsanu_gabi
2006-10-22 05:45:45 UTC
Re: Glass cutting
Tony Smith
2006-10-22 07:08:46 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
vrsculptor
2006-10-22 07:18:40 UTC
Re: Glass cutting
balsanu_gabi
2006-10-22 07:31:59 UTC
Re: Glass cutting
vrsculptor
2006-10-22 07:45:42 UTC
Re: Glass cutting
Tony Smith
2006-10-22 08:10:40 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Tony Smith
2006-10-22 09:05:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
vrsculptor
2006-10-22 11:04:30 UTC
Re: Glass cutting
Tony Smith
2006-10-22 11:32:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Jack Coats
2006-10-22 16:44:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Jack Coats
2006-10-22 16:54:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
Jon Elson
2006-10-22 17:49:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
jesse Brennan
2006-10-22 19:15:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
Tony Smith
2006-10-23 00:30:54 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Brad Eyben
2006-10-23 06:36:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
jesse Brennan
2006-10-23 07:04:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Glass cutting
optics22000
2006-10-23 10:55:40 UTC
Re: Glass cutting
Tony Smith
2006-10-23 11:16:27 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
Tony Smith
2006-10-23 11:31:49 UTC
RE: [CAD_CAM_EDM_DRO] Re: Glass cutting
balsanu_gabi
2006-10-23 13:30:41 UTC
Re: Glass cutting
optics22000
2006-10-23 22:48:05 UTC
Re: Glass cutting