Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
Posted by
Stephen Wille Padnos
on 2010-02-04 16:23:28 UTC
andrew.mathison wrote:
of EPP or ECP device, but when the driver can't get it to reset or
initialize, it disables the port. This might make sense when the
expected use of a parallel port is to communicate with things like
printers and scanners. It may also be an issue if the thing connected
to the interrupt input is in the "wrong" state while Windows is booting.
- Steve
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, Andy Wander<awander@...> wrote:The most likely explanation to me is that the BOB looks like some sort
>
>> Hey, Les:
>>
>> I had that same problem with XP(I also had it when I tried Win2K) that the PC would not boot up if the parallel ports were plugged in to the breakout boards.
>>
>> I was beginning to think I was crazy, as I reported it on the Mach forum, and nobody seemed to have ever heard or seen anything like it before.
>> ______________________________________
>> Andy Wander
>>
> Hi Andy,
> with such a problem, the reason may be that the BOB (or equivalent) is drawing far too much current from the individual pins. The boot up check is seeing this and for safety reasons its stopping the boot.
> I know its a fiddle, but you need to measure the current drawn when a pin is activated, not that easy.
> The printer port guarantees only a max of 2.6 ma as a source or 24 ma as a sink (7400 specs). That means that on a BOB with Opto isolation for example that the input resistors need to be around 2K Ohms minimum. More is OK.... I have seen preofessional BOBs with only 370 Ohms...470 Ohms is typical and completely wrong....
> Join DIY-CNC-Interfacing if you wish and read more about this. Also the printer port specs are there to read too....
> If you draw too much current, you could even damage the Printer Port (which is buried in a BIG chip that has many functions other than Printing), or even the mainboard itself. Be carefull.....
> regards
> Andy M.
>
of EPP or ECP device, but when the driver can't get it to reset or
initialize, it disables the port. This might make sense when the
expected use of a parallel port is to communicate with things like
printers and scanners. It may also be an issue if the thing connected
to the interrupt input is in the "wrong" state while Windows is booting.
- Steve
Discussion Thread
Ronald
2010-01-07 06:28:30 UTC
Compters without printer port
Stephen Wille Padnos
2010-01-07 06:35:51 UTC
Re: [CAD_CAM_EDM_DRO] Compters without printer port
caudlet
2010-01-07 06:48:25 UTC
Re: Compters without printer port
Dan Mauch
2010-01-07 09:21:01 UTC
Re: [CAD_CAM_EDM_DRO] Compters without printer port
imserv1
2010-01-08 06:19:19 UTC
Re: Compters without printer port
Danny Miller
2010-01-08 13:12:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
Mihaly Kis
2010-01-08 13:17:27 UTC
Re: [CAD_CAM_EDM_DRO] Compters without printer port
Ron Kline
2010-01-08 17:28:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
Roland Jollivet
2010-01-09 06:57:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
cbe_mannan
2010-01-11 16:20:35 UTC
Re: Compters without printer port
Art Fenerty
2010-01-11 16:21:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
erikj180
2010-02-03 10:44:19 UTC
Re: Compters without printer port
Lester Caine
2010-02-03 10:55:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
Andy Wander
2010-02-03 10:55:51 UTC
RE: [CAD_CAM_EDM_DRO] Re: Compters without printer port
Andy Wander
2010-02-03 10:59:36 UTC
RE: [CAD_CAM_EDM_DRO] Re: Compters without printer port
Lester Caine
2010-02-03 11:07:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
Danny Miller
2010-02-04 00:27:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
andrew.mathison
2010-02-04 15:22:38 UTC
Re: Compters without printer port
caudlet
2010-02-04 15:56:32 UTC
Re: Compters without printer port
Stephen Wille Padnos
2010-02-04 16:23:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
Lester Caine
2010-02-04 20:36:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
Stephen Wille Padnos
2010-02-04 20:45:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
Lester Caine
2010-02-04 21:35:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
Andrew Mathison
2010-02-05 07:39:33 UTC
Re: Compters without printer port
caudlet
2010-02-05 08:40:43 UTC
Re: Compters without printer port
Andrew Mathison
2010-02-05 10:38:24 UTC
Re: Compters without printer port
David LeVine
2010-02-05 10:58:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port
Lester Caine
2010-02-05 12:00:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Compters without printer port