CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: low cost stepper driver

Posted by John Dammeyer
on 2012-06-28 17:35:07 UTC
Hi

There are a number of people making stepper driver boards using the
LMD18245 driver chips I used in the ELS. These are good to 55VDC and 3A
and so will work with a 36V to 48V supply. They are fairly robust with a
thermal protection sensor inside. The processor that runs them takes care
of the Microstepping.

However, the smaller Gecko's end up being close to the same price so it's
hard to say if rolling your own is worth it.

John Dammeyer

"ELS! The Solution"
Automation Artisans Inc.
http://www.autoartisans.com/ELS/
Ph. 1 250 544 4950


> -----Original Message-----
> From: CAD_CAM_EDM_DRO@yahoogroups.com
> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of David G. LeVine
> Sent: Wednesday, June 27, 2012 5:34 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: Re: [CAD_CAM_EDM_DRO] Re: low cost stepper driver
>
>
> On 06/27/2012 01:20 PM, jeffalanp wrote:
> > Hi,
> >
> > I think that will really come down to the mechanics of
> mounting the motor to the table and removing backlash.
> >
> > As far as the motor is concerned, as long as it gets the
> proper power it will turn. The motor requires power from a
> servo drive, which will get position commands from a
> controller and actual position from the motors encoder. The
> controller could be stand-alone on up to a PC running
> software like LinuxCNC. If you have a servo motor with
> matching drive, you still need a control source like LinuxCNC.
> >
> > Jeff
>
> Another thing to look at is John Dammeyer's ELS project. He does
> positioning with a PIC and takes commands from a keypad and display.
> The price is pretty reasonable and it includes a stepper
> drive system.
> It is built for a lathe, and does have extra stuff, but it is
> worth it
> for the ideas... Just remember that you don't need to buy one to see
> what and how he did things, but it may be cheaper than reverse
> engineering the system.
>
> Dave 8{)
>
> --
> /"Political Correctness is a doctrine, fostered by a delusional,
> illogical minority and rabidly promoted by an unscrupulous mainstream
> media, which holds forth the proposition that it is entirely
> possible to
> pick up a turd by the clean end."/
> (quoted from http://www.wattflyer.com/forums/showthread.php?t=30060)
>
> NOTE TO ALL:
>
>
> When forwarding emails, please use only "Blind Carbon Copy"
> or "Bcc" for
> all recipients. Please "delete" or "highlight & cut" any forwarding
> history which includes my email address! It is a courtesy to me and
> others who may not wish to have their email addresses sent
> all over the
> world! Erasing the history helps prevent Spammers from mining
> addresses
> and viruses from being propagated.
>
> THANK YOU!
>
>
> [Non-text portions of this message have been removed]
>
>
>
> ------------------------------------
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@..., timg@...
> Moderator: pentam@... indigo_red@...
> davemucha@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com
> to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider
> this to be a sister site to the CCED group, as many of the
> same members are there, for OT subjects, that are not allowed
> on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> EXCEPTIONS........
> bill
> List Mom
> List Owner
>
> Yahoo! Groups Links
>
>
>
>

Discussion Thread

turbulatordude 2012-06-25 17:51:22 UTC low cost stepper driver Ron Thompson 2012-06-26 04:33:51 UTC Re: [CAD_CAM_EDM_DRO] low cost stepper driver Jamie Cunningham 2012-06-26 04:55:38 UTC Re: [CAD_CAM_EDM_DRO] low cost stepper driver Tony Smith 2012-06-26 06:06:24 UTC RE: [CAD_CAM_EDM_DRO] low cost stepper driver Ron Thompson 2012-06-26 06:53:07 UTC Re: [CAD_CAM_EDM_DRO] low cost stepper driver Tony Smith 2012-06-26 07:16:46 UTC RE: [CAD_CAM_EDM_DRO] low cost stepper driver Dan Mauch 2012-06-26 07:43:39 UTC RE: [CAD_CAM_EDM_DRO] low cost stepper driver jeffalanp 2012-06-26 11:54:37 UTC Re: low cost stepper driver Nelson Collar 2012-06-26 12:58:22 UTC Re: [CAD_CAM_EDM_DRO] Re: low cost stepper driver Dr Stuart Harrison 2012-06-26 15:00:53 UTC RE: [CAD_CAM_EDM_DRO] low cost stepper driver jeffalanp 2012-06-26 16:38:30 UTC Re: low cost stepper driver Nelson Collar 2012-06-26 18:18:08 UTC Re: [CAD_CAM_EDM_DRO] Re: low cost stepper driver jeffalanp 2012-06-27 11:50:50 UTC Re: low cost stepper driver David G. LeVine 2012-06-27 17:33:58 UTC Re: [CAD_CAM_EDM_DRO] Re: low cost stepper driver John Dammeyer 2012-06-28 17:35:07 UTC RE: [CAD_CAM_EDM_DRO] Re: low cost stepper driver Lester Caine 2012-06-30 06:45:37 UTC RE: [CAD_CAM_EDM_DRO] low cost stepper driver John Dammeyer 2012-06-30 06:50:12 UTC RE: [CAD_CAM_EDM_DRO] Re: low cost stepper driver artgartg 2012-09-30 19:44:58 UTC Re: low cost stepper driver Ron Ginger 2012-10-01 04:23:09 UTC Re:low cost stepper driver turbulatordude 2012-10-01 04:41:13 UTC Re:low cost stepper driver Jamie Cunningham 2012-10-01 05:01:05 UTC Re: [CAD_CAM_EDM_DRO] Re:low cost stepper driver rwwink 2012-10-01 06:13:45 UTC RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver Jeffrey Birt 2012-10-01 06:49:39 UTC RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver John Dammeyer 2012-10-01 08:34:28 UTC RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver David G. LeVine 2012-10-01 12:22:27 UTC Re: [CAD_CAM_EDM_DRO] Re:low cost stepper driver Tony Smith 2012-10-01 13:15:24 UTC RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver Ron Thompson 2012-10-01 13:59:56 UTC Re: [CAD_CAM_EDM_DRO] Re:low cost stepper driver turbulatordude 2012-10-01 16:57:37 UTC Re:low cost stepper driver Dr Stuart Harrison 2012-10-01 20:27:49 UTC RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver Tony Smith 2012-10-01 22:51:44 UTC RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver Lester Caine 2012-10-02 00:23:21 UTC Re: ***SPAM*** [CAD_CAM_EDM_DRO] Re:low cost stepper driver wotisname 2012-10-02 04:20:51 UTC Re:low cost stepper driver artgartg 2012-10-02 12:10:13 UTC Re:low cost stepper driver artgartg 2012-10-02 12:10:41 UTC Re:low cost stepper driver artgartg 2012-10-02 12:10:56 UTC Re:low cost stepper driver Joe 2012-10-02 12:11:27 UTC Re:low cost stepper driver Stephen Muscato 2012-10-02 12:31:11 UTC Re: [CAD_CAM_EDM_DRO] Re:low cost stepper driver John Dammeyer 2012-10-02 22:15:21 UTC RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver Tony Smith 2012-10-03 02:46:10 UTC RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver turbulatordude 2012-10-03 04:36:09 UTC Re:low cost stepper driver Tony Smith 2012-10-03 08:31:49 UTC RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver