Re: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
Posted by
Stephen Muscato
on 2012-10-02 12:31:11 UTC
Folks,
At this point I will tell of my experience with a loose wire.
My machine was having an intermittent problem sometimes it would run for a week or more.
When it acted up it was terrible! Loud noises and oscillations.
I managed to finally see the sparking of the wire in the connector as it acted up.
A loose wire on the plug going to the stepper.
All my drivers are Keling, and what should have probably destroyed the driver did not.
I'm a very satisfied customer. You get what you pay for.
Steve
________________________________
From: artgartg <lists@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com
Sent: Tuesday, October 2, 2012 2:05 PM
Subject: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Tony Smith" >
-adrian
[Non-text portions of this message have been removed]
At this point I will tell of my experience with a loose wire.
My machine was having an intermittent problem sometimes it would run for a week or more.
When it acted up it was terrible! Loud noises and oscillations.
I managed to finally see the sparking of the wire in the connector as it acted up.
A loose wire on the plug going to the stepper.
All my drivers are Keling, and what should have probably destroyed the driver did not.
I'm a very satisfied customer. You get what you pay for.
Steve
________________________________
From: artgartg <lists@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com
Sent: Tuesday, October 2, 2012 2:05 PM
Subject: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Tony Smith" >
>Indeed, It's all very well being careful about how you connect and disconnect but if a wire breaks, I want to repair the wire, not the stepper board. Good design makes things robust against accidental failure as well as user error.
>
> As you say it won't happen much in real life, but there is always the
> possibility of a lead coming out due to vibration or being bumped by
> accident.
>
> Tony
>
-adrian
[Non-text portions of this message have been removed]
Discussion Thread
turbulatordude
2012-06-25 17:51:22 UTC
low cost stepper driver
Ron Thompson
2012-06-26 04:33:51 UTC
Re: [CAD_CAM_EDM_DRO] low cost stepper driver
Jamie Cunningham
2012-06-26 04:55:38 UTC
Re: [CAD_CAM_EDM_DRO] low cost stepper driver
Tony Smith
2012-06-26 06:06:24 UTC
RE: [CAD_CAM_EDM_DRO] low cost stepper driver
Ron Thompson
2012-06-26 06:53:07 UTC
Re: [CAD_CAM_EDM_DRO] low cost stepper driver
Tony Smith
2012-06-26 07:16:46 UTC
RE: [CAD_CAM_EDM_DRO] low cost stepper driver
Dan Mauch
2012-06-26 07:43:39 UTC
RE: [CAD_CAM_EDM_DRO] low cost stepper driver
jeffalanp
2012-06-26 11:54:37 UTC
Re: low cost stepper driver
Nelson Collar
2012-06-26 12:58:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: low cost stepper driver
Dr Stuart Harrison
2012-06-26 15:00:53 UTC
RE: [CAD_CAM_EDM_DRO] low cost stepper driver
jeffalanp
2012-06-26 16:38:30 UTC
Re: low cost stepper driver
Nelson Collar
2012-06-26 18:18:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: low cost stepper driver
jeffalanp
2012-06-27 11:50:50 UTC
Re: low cost stepper driver
David G. LeVine
2012-06-27 17:33:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: low cost stepper driver
John Dammeyer
2012-06-28 17:35:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: low cost stepper driver
Lester Caine
2012-06-30 06:45:37 UTC
RE: [CAD_CAM_EDM_DRO] low cost stepper driver
John Dammeyer
2012-06-30 06:50:12 UTC
RE: [CAD_CAM_EDM_DRO] Re: low cost stepper driver
artgartg
2012-09-30 19:44:58 UTC
Re: low cost stepper driver
Ron Ginger
2012-10-01 04:23:09 UTC
Re:low cost stepper driver
turbulatordude
2012-10-01 04:41:13 UTC
Re:low cost stepper driver
Jamie Cunningham
2012-10-01 05:01:05 UTC
Re: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
rwwink
2012-10-01 06:13:45 UTC
RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
Jeffrey Birt
2012-10-01 06:49:39 UTC
RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
John Dammeyer
2012-10-01 08:34:28 UTC
RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
David G. LeVine
2012-10-01 12:22:27 UTC
Re: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
Tony Smith
2012-10-01 13:15:24 UTC
RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
Ron Thompson
2012-10-01 13:59:56 UTC
Re: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
turbulatordude
2012-10-01 16:57:37 UTC
Re:low cost stepper driver
Dr Stuart Harrison
2012-10-01 20:27:49 UTC
RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
Tony Smith
2012-10-01 22:51:44 UTC
RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
Lester Caine
2012-10-02 00:23:21 UTC
Re: ***SPAM*** [CAD_CAM_EDM_DRO] Re:low cost stepper driver
wotisname
2012-10-02 04:20:51 UTC
Re:low cost stepper driver
artgartg
2012-10-02 12:10:13 UTC
Re:low cost stepper driver
artgartg
2012-10-02 12:10:41 UTC
Re:low cost stepper driver
artgartg
2012-10-02 12:10:56 UTC
Re:low cost stepper driver
Joe
2012-10-02 12:11:27 UTC
Re:low cost stepper driver
Stephen Muscato
2012-10-02 12:31:11 UTC
Re: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
John Dammeyer
2012-10-02 22:15:21 UTC
RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
Tony Smith
2012-10-03 02:46:10 UTC
RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver
turbulatordude
2012-10-03 04:36:09 UTC
Re:low cost stepper driver
Tony Smith
2012-10-03 08:31:49 UTC
RE: [CAD_CAM_EDM_DRO] Re:low cost stepper driver