Re: [CAD_CAM_EDM_DRO] Re: greetings
Posted by
Darrell
on 2000-09-18 21:26:35 UTC
Guess you are going to have to get a real internet connection and leave
AOhelL to the kids.
Darrell
AOhelL to the kids.
Darrell
----- Original Message -----
From: <JanRwl@...>
To: <CAD_CAM_EDM_DRO@egroups.com>
Sent: Monday, September 18, 2000 9:13 PM
Subject: Re: [CAD_CAM_EDM_DRO] Re: greetings
>
> In a message dated 18-Sep-00 23:10:43 Central Daylight Time,
> dgehlsen@... writes:
>
> << For ballscrews.com type the following in the address bar instead of
> www.ballscrews.com
>
> 209.219.67.162
>
> that will get you there.
> Darrell >>
>
> Does not! Takes SEVERAL minutes, and finally repeats this number, "No
such
> address..." (or whatever wording)!
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>
Discussion Thread
Dan Dowell
2000-09-16 22:21:52 UTC
Re: greetings
Alvaro Fogassa
2000-09-16 23:28:25 UTC
Re: greetings
Tim Goldstein
2000-09-17 09:43:14 UTC
#40 tapers?
machines@n...
2000-09-17 13:36:42 UTC
Re: #40 tapers?
Ray
2000-09-17 15:48:48 UTC
Re: greetings
Alvaro Fogassa
2000-09-17 21:08:12 UTC
Re: greetings
ballendo@y...
2000-09-18 00:18:46 UTC
Re: Re: greetings
Ray
2000-09-18 07:35:34 UTC
Re: Re: greetings
Lee & Chris studley
2000-09-18 08:50:23 UTC
Air assisted ball/screw on Z axis(table height) ?
Alvaro Fogassa
2000-09-18 12:12:12 UTC
Re: greetings
JanRwl@A...
2000-09-18 17:24:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
JanRwl@A...
2000-09-18 17:26:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
JanRwl@A...
2000-09-18 17:39:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: greetings
bfp
2000-09-18 17:57:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
dave engvall
2000-09-18 18:48:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
JanRwl@A...
2000-09-18 19:57:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
Doug Warner
2000-09-18 19:57:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
Mike Gann
2000-09-18 20:20:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
dave engvall
2000-09-18 20:25:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
Darrell
2000-09-18 21:09:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
JanRwl@A...
2000-09-18 21:13:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
Darrell
2000-09-18 21:26:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
ballendo@y...
2000-09-18 21:26:50 UTC
Re: Re: greetings
Darrell
2000-09-18 21:32:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
dave engvall
2000-09-18 21:34:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
ballendo@y...
2000-09-18 21:35:01 UTC
Re: Re: greetings
Dan Dowell
2000-09-18 21:39:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
Darrell
2000-09-18 21:42:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: greetings
ballendo@y...
2000-09-18 22:07:26 UTC
Re: Re: Re: greetings
Jon Elson
2000-09-18 22:26:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
Darrell
2000-09-19 09:18:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: greetings
Alan Marconett KM6VV
2000-09-19 10:33:47 UTC
Re: greetings
Alan Marconett KM6VV
2000-09-19 10:43:58 UTC
Re: greetings
JanRwl@A...
2000-09-19 20:48:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: greetings