Re: [CAD_CAM_EDM_DRO] Re: greetings
Posted by
dave engvall
on 2000-09-18 21:34:54 UTC
JanRwl@... wrote:
If you can find where to set it try setting the secondary dns to something besides aol. I don't know if this is possible with the
aol software.
Also try dialing into aol then run netscape on top of aol. It may not help but who knows.
Actually what you need is a way to set primary and secondary dns's. These are set within the isp access software so aol may have
left you out in the cold.
Dave
> In a message dated 18-Sep-00 23:10:43 Central Daylight Time,The ip is good. I get about 325 ms. on ping. Aol's DNS is clearly having a problem.
> dgehlsen@... writes:
>
> << For ballscrews.com type the following in the address bar instead of
> www.ballscrews.com
>
> 209.219.67.162
>
> that will get you there.
> Darrell >>
>
If you can find where to set it try setting the secondary dns to something besides aol. I don't know if this is possible with the
aol software.
Also try dialing into aol then run netscape on top of aol. It may not help but who knows.
Actually what you need is a way to set primary and secondary dns's. These are set within the isp access software so aol may have
left you out in the cold.
Dave
Discussion Thread
Dan Dowell
2000-09-16 22:21:52 UTC
Re: greetings
Alvaro Fogassa
2000-09-16 23:28:25 UTC
Re: greetings
Tim Goldstein
2000-09-17 09:43:14 UTC
#40 tapers?
machines@n...
2000-09-17 13:36:42 UTC
Re: #40 tapers?
Ray
2000-09-17 15:48:48 UTC
Re: greetings
Alvaro Fogassa
2000-09-17 21:08:12 UTC
Re: greetings
ballendo@y...
2000-09-18 00:18:46 UTC
Re: Re: greetings
Ray
2000-09-18 07:35:34 UTC
Re: Re: greetings
Lee & Chris studley
2000-09-18 08:50:23 UTC
Air assisted ball/screw on Z axis(table height) ?
Alvaro Fogassa
2000-09-18 12:12:12 UTC
Re: greetings
JanRwl@A...
2000-09-18 17:24:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
JanRwl@A...
2000-09-18 17:26:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
JanRwl@A...
2000-09-18 17:39:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: greetings
bfp
2000-09-18 17:57:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
dave engvall
2000-09-18 18:48:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
JanRwl@A...
2000-09-18 19:57:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
Doug Warner
2000-09-18 19:57:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
Mike Gann
2000-09-18 20:20:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
dave engvall
2000-09-18 20:25:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
Darrell
2000-09-18 21:09:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
JanRwl@A...
2000-09-18 21:13:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
Darrell
2000-09-18 21:26:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
ballendo@y...
2000-09-18 21:26:50 UTC
Re: Re: greetings
Darrell
2000-09-18 21:32:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
dave engvall
2000-09-18 21:34:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
ballendo@y...
2000-09-18 21:35:01 UTC
Re: Re: greetings
Dan Dowell
2000-09-18 21:39:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
Darrell
2000-09-18 21:42:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: greetings
ballendo@y...
2000-09-18 22:07:26 UTC
Re: Re: Re: greetings
Jon Elson
2000-09-18 22:26:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: greetings
Darrell
2000-09-19 09:18:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: greetings
Alan Marconett KM6VV
2000-09-19 10:33:47 UTC
Re: greetings
Alan Marconett KM6VV
2000-09-19 10:43:58 UTC
Re: greetings
JanRwl@A...
2000-09-19 20:48:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: greetings