CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: greetings

Posted by Darrell
on 2000-09-18 21:32:11 UTC
It comes up for me using the number or the link with Earthlink as the ISP
Darrell

----- Original Message -----
From: <JanRwl@...>
To: <CAD_CAM_EDM_DRO@egroups.com>
Sent: Monday, September 18, 2000 9:13 PM
Subject: Re: [CAD_CAM_EDM_DRO] Re: greetings


>
> In a message dated 18-Sep-00 23:10:43 Central Daylight Time,
> dgehlsen@... writes:
>
> << For ballscrews.com type the following in the address bar instead of
> www.ballscrews.com
>
> 209.219.67.162
>
> that will get you there.
> Darrell >>
>
> Does not! Takes SEVERAL minutes, and finally repeats this number, "No
such
> address..." (or whatever wording)!
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>

Discussion Thread

Dan Dowell 2000-09-16 22:21:52 UTC Re: greetings Alvaro Fogassa 2000-09-16 23:28:25 UTC Re: greetings Tim Goldstein 2000-09-17 09:43:14 UTC #40 tapers? machines@n... 2000-09-17 13:36:42 UTC Re: #40 tapers? Ray 2000-09-17 15:48:48 UTC Re: greetings Alvaro Fogassa 2000-09-17 21:08:12 UTC Re: greetings ballendo@y... 2000-09-18 00:18:46 UTC Re: Re: greetings Ray 2000-09-18 07:35:34 UTC Re: Re: greetings Lee & Chris studley 2000-09-18 08:50:23 UTC Air assisted ball/screw on Z axis(table height) ? Alvaro Fogassa 2000-09-18 12:12:12 UTC Re: greetings JanRwl@A... 2000-09-18 17:24:56 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings JanRwl@A... 2000-09-18 17:26:29 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings JanRwl@A... 2000-09-18 17:39:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: greetings bfp 2000-09-18 17:57:01 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings dave engvall 2000-09-18 18:48:05 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings JanRwl@A... 2000-09-18 19:57:30 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings Doug Warner 2000-09-18 19:57:44 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings Mike Gann 2000-09-18 20:20:37 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings dave engvall 2000-09-18 20:25:19 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings Darrell 2000-09-18 21:09:15 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings JanRwl@A... 2000-09-18 21:13:43 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings Darrell 2000-09-18 21:26:35 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings ballendo@y... 2000-09-18 21:26:50 UTC Re: Re: greetings Darrell 2000-09-18 21:32:11 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings dave engvall 2000-09-18 21:34:54 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings ballendo@y... 2000-09-18 21:35:01 UTC Re: Re: greetings Dan Dowell 2000-09-18 21:39:31 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings Darrell 2000-09-18 21:42:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: greetings ballendo@y... 2000-09-18 22:07:26 UTC Re: Re: Re: greetings Jon Elson 2000-09-18 22:26:48 UTC Re: [CAD_CAM_EDM_DRO] Re: greetings Darrell 2000-09-19 09:18:22 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Re: greetings Alan Marconett KM6VV 2000-09-19 10:33:47 UTC Re: greetings Alan Marconett KM6VV 2000-09-19 10:43:58 UTC Re: greetings JanRwl@A... 2000-09-19 20:48:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: greetings