CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: HF Bandsaw converted to CNC

Posted by Smoke
on 2001-05-04 23:29:49 UTC
Since were talking two different types of saws here, sholud I presume the HF
stands for "horizontal feed"?
If so, that would explain why the rest of you get more accurate cuts than I
do with my cutoff saw.

Smoke




>Smoke,
>
>My conversion is on a cold saw. Unlike a bandsaw these things won't
>gravity feed. Depending on what's being cut the operator may have to
>exert a fair amount of downward force on the operating lever. The
>force could easily be 50 pounds or more. Gets really old if you have
>a number of cuts to make.
>
>Doug
>
>--- In CAD_CAM_EDM_DRO@y..., "Smoke" <gordonr@r...> wrote:
>> Why all the controls? All mine has is a hydraulic cylinder, a flow
>control
>> valve and a shut off valve. The shutoff valve is used to hold the
>saw in a
>> partially raised position while adjusting the work. The flow control
>> controls the rate of down feed.
>>
>> No relays, switches, etc required.
>>
>> Smoke
>>
>>
>>
>> >Jon,
>> >
>> >I'm in the process of converting my cold saw to hydraulic downfeed.
>> >Air could probably be used as well, although I like low pressure
>> >hydraulic better. I'll adjust feed rate with a flow control valve.
>> >
>> >The hydraulic or air method simplifies things. A relay, start
>> >button, and a couple limit switches are all the controls needed.
>And
>> >an emergency stop, of course.
>> >
>> >Doug
>> >
>> >--- In CAD_CAM_EDM_DRO@y..., Jon Anderson <janders@n...> wrote:
>> >> Dan,
>> >>
>> >> Funny you should write about this. While I'd really like to find
>an
>> >> automatic cold saw with a dead control, even that isn't going to
>be
>> >> cheap. I've been thinking about converting my HV saw (an older
>> >Clausing)
>> >> and wondered about the feed control on the saw. If a feed rate
>was
>> >> programmed that was even a bit too fast for the cut, it could
>cause
>> >the
>> >> blade to wander, or even break on deep cuts.
>> >> I've been thinking about some form of control that would allow
>feed
>> >> based on pressure. Something along the lines of the Z screw being
>> >> attached to a mechanism whereby the saw frame would float between
>> >two
>> >> springs, and an adjustable micro switch would contact the frame
>> >under
>> >> some adjustable amount of preload. The upper spring and gravity
>> >would
>> >> provide down feed to the point where the two springs equalize, at
>> >which
>> >> point the Z motor would start feeding until getting a signal from
>> >the
>> >> limit switch that the desired preload level had been reached.
>> >>
>> >> Did you do anything like this at all, or did you just adjust feed
>> >rates
>> >> until you were happy with the cut?
>> >>
>> >> Jon
>> >
>> >
>> >Welcome to CAD_CAM_EDM_DRO@e...,an unmoderated list for the
>> discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>> >
>> >Addresses:
>> >Post message: CAD_CAM_EDM_DRO@y...
>> >Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
>> >Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
>> >List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
>> >Moderator: jmelson@a... timg@k... [Moderator]
>> >URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>> >bill,
>> >List Manager
>> >
>> >FAQ: http://www.ktmarketing.com/faq.html
>> >
>> >Your use of Yahoo! Groups is subject to
>http://docs.yahoo.com/info/terms/
>> >
>> >
>
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
>Addresses:
>Post message: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>FAQ: http://www.ktmarketing.com/faq.html
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>

Discussion Thread

Dan Mauch 2001-05-04 07:04:28 UTC Re: [CAD_CAM_EDM_DRO] HF Bandsaw converted to CNC Jon Anderson 2001-05-04 07:42:06 UTC Re: [CAD_CAM_EDM_DRO] HF Bandsaw converted to CNC Dan Mauch 2001-05-04 10:47:20 UTC Re: [CAD_CAM_EDM_DRO] HF Bandsaw converted to CNC dougrasmussen@c... 2001-05-04 12:27:24 UTC Re: HF Bandsaw converted to CNC Smoke 2001-05-04 14:00:15 UTC Re: [CAD_CAM_EDM_DRO] Re: HF Bandsaw converted to CNC Sven Peter, TAD S.A. 2001-05-04 18:32:08 UTC Re: [CAD_CAM_EDM_DRO] HF Bandsaw converted to CNC Jon Anderson 2001-05-04 19:30:58 UTC Re: [CAD_CAM_EDM_DRO] HF Bandsaw converted to CNC dougrasmussen@c... 2001-05-04 22:16:46 UTC Re: HF Bandsaw converted to CNC Smoke 2001-05-04 23:29:49 UTC Re: [CAD_CAM_EDM_DRO] Re: HF Bandsaw converted to CNC stratton@m... 2001-05-05 07:40:23 UTC Re: [CAD_CAM_EDM_DRO] Re: HF Bandsaw converted to CNC Tim Goldstein 2001-05-05 10:00:34 UTC RE: [CAD_CAM_EDM_DRO] Re: HF Bandsaw converted to CNC Sven Peter, TAD S.A. 2001-05-05 14:52:37 UTC Re: [CAD_CAM_EDM_DRO] HF Bandsaw converted to CNC Sven Peter, TAD S.A. 2001-05-05 15:03:53 UTC Re: [CAD_CAM_EDM_DRO] Re: HF Bandsaw converted to CNC Jon Anderson 2001-05-05 15:06:05 UTC Re: [CAD_CAM_EDM_DRO] HF Bandsaw converted to CNC Smoke 2001-05-05 23:56:20 UTC Re: [CAD_CAM_EDM_DRO] Re: HF Bandsaw converted to CNC Smoke 2001-05-06 00:10:56 UTC Re: [CAD_CAM_EDM_DRO] Re: HF Bandsaw converted to CNC wanliker@a... 2001-05-06 01:07:47 UTC Re: [CAD_CAM_EDM_DRO] Re: HF Bandsaw converted to CNC ptengin@a... 2001-05-06 15:29:18 UTC Re: [CAD_CAM_EDM_DRO] Re: HF Bandsaw converted to CNC Smoke 2001-05-07 09:52:50 UTC Re: [CAD_CAM_EDM_DRO] Re: HF Bandsaw converted to CNC Sven Peter, TAD S.A. 2001-05-08 08:41:18 UTC Re: [CAD_CAM_EDM_DRO] HF Bandsaw converted to CNC