Re: [CAD_CAM_EDM_DRO] LPKF 2d drill
Posted by
Jon Elson
on 2001-05-18 10:07:13 UTC
"Zoran A. Scepanovic" wrote:
however. Look for Vexta and Oriental Motor for info on these motors. IF they are 5-phase, you
will have to use Vexta or Berger-Lahr drivers on them, as they own the patents. If you can figure
out the connections to the "unusually scratched chip" to drive it, then maybe you can use
the drivers as is.
Jon
> Hi all,Oh OH! Ten wires sounds like 5-phase motors, which are rather oddball. They perform VERY well,
>
> I just got from a friend a CNC drill as in the subject. It is an PCB drilling machine with only two axes (X & Y, Z is driven by an electromagnet).
> The motors that are fitted onto this machine are steppers, but with no markings on them. They have 10 wires, and the wire pairs are as follows:
>
> gray + black
> blue + red
> violet + brown
> green + orange
> yellow + white
>
> (could not measure the resistances of the windings cause my DVM just broke)
> The motors are 59mm x 108mm in size.
>
> The drivers are consisted of an unusualy scratched chip connected to 3 (three) L298 (2 1/2).
however. Look for Vexta and Oriental Motor for info on these motors. IF they are 5-phase, you
will have to use Vexta or Berger-Lahr drivers on them, as they own the patents. If you can figure
out the connections to the "unusually scratched chip" to drive it, then maybe you can use
the drivers as is.
Jon
Discussion Thread
Zoran A. Scepanovic
2001-05-18 06:59:22 UTC
LPKF 2d drill
Joe Burns
2001-05-18 07:28:19 UTC
Old Trak DRO Encoder Heads
Jon Anderson
2001-05-18 07:56:10 UTC
Re: [CAD_CAM_EDM_DRO] Old Trak DRO Encoder Heads
Joe Burns
2001-05-18 08:11:43 UTC
Re: [CAD_CAM_EDM_DRO] Old Trak DRO Encoder Heads
Jon Elson
2001-05-18 10:07:13 UTC
Re: [CAD_CAM_EDM_DRO] LPKF 2d drill
Alan Marconett KM6VV
2001-05-18 18:20:34 UTC
Re: [CAD_CAM_EDM_DRO] LPKF 2d drill
Zoran A. Scepanovic
2001-05-19 08:01:12 UTC
Re: [CAD_CAM_EDM_DRO] LPKF 2d drill
Jerry Kimberlin
2001-05-19 08:27:49 UTC
Re: [CAD_CAM_EDM_DRO] LPKF 2d drill
Carey L. Culpepper
2001-05-19 10:24:21 UTC
Re: [CAD_CAM_EDM_DRO] LPKF 2d drill
Brian Pitt
2001-05-19 15:05:51 UTC
Re: [CAD_CAM_EDM_DRO] LPKF 2d drill
Alan Marconett KM6VV
2001-05-19 20:41:45 UTC
Re: [CAD_CAM_EDM_DRO] LPKF 2d drill
Alan Marconett KM6VV
2001-05-19 20:56:10 UTC
Re: [CAD_CAM_EDM_DRO] LPKF 2d drill
Jerry Kimberlin
2001-05-20 06:50:03 UTC
Re: [CAD_CAM_EDM_DRO] LPKF 2d drill
Alan Marconett KM6VV
2001-05-20 17:44:40 UTC
Re: [CAD_CAM_EDM_DRO] LPKF 2d drill
ballendo@y...
2001-05-21 20:47:34 UTC
Re: LPKF 2d drill
Rich D.
2001-05-21 21:12:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPKF 2d drill
ballendo@y...
2001-05-21 21:17:25 UTC
Re: LPKF 2d drill
Zoran A. Scepanovic
2001-05-22 01:19:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPKF 2d drill
admin@a...
2001-05-23 21:21:25 UTC
Re: LPKF 2d drill
ballendo@y...
2001-05-24 20:52:43 UTC
Re: LPKF 2d drill
admin@a...
2001-05-25 16:30:06 UTC
Re: LPKF 2d drill
currinh@O...
2001-06-12 21:29:44 UTC
Re: Old Trak DRO Encoder Heads
Karen
2001-07-04 09:00:37 UTC
Re: LPKF 2d drill
Alan Marconett KM6VV
2001-07-04 10:46:41 UTC
Re: LPKF 2d drill
Karen Winters
2001-07-04 11:43:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPKF 2d drill
Alan Marconett KM6VV
2001-07-04 18:40:16 UTC
Re: LPKF 2d drill