Re: [CAD_CAM_EDM_DRO] Re: EMC problem/question
Posted by
Jon Elson
on 2001-08-06 20:52:25 UTC
currinh@... wrote:
through with the same polarity as you have with the direct connection.
Jon
> Jon:Yes, it should.
>
> I got a chance to try "freqmod" as you suggest. After some futzing I
> was able to get good motion from both X & Y. The P parameter was the
> original problem. I went down to 100 and then started back up getting
> to around 500 with good motion. I did set a dwell of .0005" which
> stopped the dithering. I think I'm getting faster motion from freqmod
> than steppermod but as yet have no numbers.
> I didn't put theI suspect it will have the same trouble. You need to send the step pulse
> opto-isolation back in to see if it works with freqmod though.
through with the same polarity as you have with the direct connection.
Jon
Discussion Thread
Randy Poon
2001-08-03 08:59:32 UTC
[CAD_CAM_EDM_DRO] RTV Mold
Smoke
2001-08-03 09:44:17 UTC
Re: [CAD_CAM_EDM_DRO] RTV Mold
Alan King
2001-08-03 09:48:49 UTC
Re: [CAD_CAM_EDM_DRO] RTV Mold
info.host@b...
2001-08-03 10:11:08 UTC
Re: [CAD_CAM_EDM_DRO] RTV Mold
Scott A. Stephens
2001-08-03 10:27:40 UTC
Re: [CAD_CAM_EDM_DRO] RTV Mold
oliver_lang1@y...
2001-08-03 10:43:29 UTC
Re: RTV Mold
JanRwl@A...
2001-08-03 12:42:07 UTC
Re: [CAD_CAM_EDM_DRO] RTV Mold
John and Cindy Carey
2001-08-03 15:42:37 UTC
Re: [CAD_CAM_EDM_DRO] RTV Mold
Hugh & Denise Currin
2001-08-04 13:25:43 UTC
EMC problem/question
Tim Goldstein
2001-08-04 13:44:18 UTC
RE: [CAD_CAM_EDM_DRO] EMC problem/question
Hugh & Denise Currin
2001-08-04 16:05:28 UTC
Re: EMC problem/question
Jon Elson
2001-08-04 20:57:56 UTC
Re: [CAD_CAM_EDM_DRO] EMC problem/question
Ian Wright
2001-08-05 04:05:56 UTC
Re: [CAD_CAM_EDM_DRO] EMC problem/question
currinh@O...
2001-08-05 12:42:27 UTC
Re: EMC problem/question
currinh@O...
2001-08-05 13:00:17 UTC
Re: EMC problem/question
Jon Elson
2001-08-05 15:19:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC problem/question
Paul
2001-08-05 16:49:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC problem/question
currinh@O...
2001-08-05 17:35:04 UTC
Re: EMC problem/question
Jon Elson
2001-08-05 20:59:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC problem/question
currinh@O...
2001-08-06 19:03:40 UTC
Re: EMC problem/question
Jon Elson
2001-08-06 20:52:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC problem/question