Re: [CAD_CAM_EDM_DRO] power supply
Posted by
Alan Marconett KM6VV
on 2001-10-16 11:02:42 UTC
Hi Peter,
What's your line (mains) voltage? Might just be high. And what primary
taps are you using? Most larger transformers of this type have
something like 115V and 120V taps. You might need to change the tap!
The transformer ratios are quite accurate, YIVMV (Your input voltage
might vary). ;>)
Alan KM6VV
P.S. A big screwdriver works to discharge a cap! POW! Not that I would
do that. ;>)
cadcamcenter@... wrote:
What's your line (mains) voltage? Might just be high. And what primary
taps are you using? Most larger transformers of this type have
something like 115V and 120V taps. You might need to change the tap!
The transformer ratios are quite accurate, YIVMV (Your input voltage
might vary). ;>)
Alan KM6VV
P.S. A big screwdriver works to discharge a cap! POW! Not that I would
do that. ;>)
cadcamcenter@... wrote:
>
> How dependable are transformer specs?
>
> A Single phase 0-115-230V primary 24VAC secondary connected to a
> bridge rectifier and 15,000uF capacitor should produce 33 VDC. The
> actual output was 46VDC. The culprit? On checking the transformer
> secondary, the output was 33VAC instead of the specified 24VAC. Is
> this common experience?
>
> Based on what had been so emphatically put across recently, one
> should have no hesitation on using this power supply despite it being
> out of specs - voltage being so unimportant for steppers, right?
>
> Just to be on the safe side - what size zener diode should one place
> across the output?
>
> Peter
>
> BTW one should take care to discharge the capacitor, say, across an
> incandescent lamp at end of test.
Discussion Thread
wanliker@a...
2001-10-14 12:06:43 UTC
Members
Art Fenerty
2001-10-14 12:51:59 UTC
Re: [CAD_CAM_EDM_DRO] Members
JanRwl@A...
2001-10-14 13:23:28 UTC
Re: [CAD_CAM_EDM_DRO] Members
cadcamcenter@y...
2001-10-14 17:38:02 UTC
Re: Members
Art Fenerty
2001-10-14 18:38:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
JanRwl@A...
2001-10-14 18:43:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
Art Fenerty
2001-10-14 19:07:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
cadcamcenter@y...
2001-10-14 19:19:07 UTC
Re: Members
Tim Goldstein
2001-10-14 19:57:00 UTC
RE: [CAD_CAM_EDM_DRO] Re: Members
wanliker@a...
2001-10-14 21:08:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
cadcamcenter@y...
2001-10-15 06:24:45 UTC
Re: Members
Tim Goldstein
2001-10-15 07:05:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
JanRwl@A...
2001-10-15 09:57:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
Alan Marconett KM6VV
2001-10-15 11:30:33 UTC
Re: Members
Tim
2001-10-15 12:41:25 UTC
RE: [CAD_CAM_EDM_DRO] Re: Members
Art Fenerty
2001-10-15 12:45:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
machines@n...
2001-10-15 13:31:45 UTC
Re: Members
Art Fenerty
2001-10-15 14:44:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
Alan Trest
2001-10-15 15:47:26 UTC
Re: Members
cadcamcenter@y...
2001-10-15 16:30:21 UTC
Re: Members
Alan Marconett KM6VV
2001-10-15 17:02:57 UTC
Re: Members
Tom Murray
2001-10-15 18:37:21 UTC
Re: Members
brian
2001-10-15 19:48:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
Sven Peter
2001-10-15 20:37:06 UTC
Re: [CAD_CAM_EDM_DRO]Members
Michael Dhabolt
2001-10-15 20:55:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
Jon Elson
2001-10-15 22:04:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
Jon Elson
2001-10-15 22:08:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
Carol & Jerry Jankura
2001-10-16 06:22:48 UTC
RE: [CAD_CAM_EDM_DRO] Re: Members
Smoke
2001-10-16 07:10:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
HighTech
2001-10-16 08:00:31 UTC
RE: [CAD_CAM_EDM_DRO] Re: Members
Jon Elson
2001-10-16 10:16:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
Jon Elson
2001-10-16 10:28:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
Smoke
2001-10-16 10:29:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
cadcamcenter@y...
2001-10-16 10:31:08 UTC
power supply
Bob Campbell
2001-10-16 11:00:09 UTC
Re: [CAD_CAM_EDM_DRO] power supply
Alan Marconett KM6VV
2001-10-16 11:02:42 UTC
Re: [CAD_CAM_EDM_DRO] power supply
Carol & Jerry Jankura
2001-10-16 11:11:20 UTC
RE: [CAD_CAM_EDM_DRO] Re: Members
Art Fenerty
2001-10-16 11:18:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
Les Newell
2001-10-16 12:27:16 UTC
Re: [CAD_CAM_EDM_DRO] power supply
mariss92705@y...
2001-10-16 13:11:55 UTC
Re: Members
beer@s...
2001-10-16 13:17:04 UTC
Re: Members
Paul
2001-10-16 14:39:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
beer@s...
2001-10-16 15:55:58 UTC
Re: power supply
JanRwl@A...
2001-10-16 16:37:40 UTC
Re: [CAD_CAM_EDM_DRO] power supply
cadcamcenter@y...
2001-10-16 16:51:42 UTC
Re: power supply
mariss92705@y...
2001-10-16 17:26:20 UTC
Re: power supply
mariss92705@y...
2001-10-16 17:30:24 UTC
Re: power supply
Alan Marconett KM6VV
2001-10-16 17:36:19 UTC
Re: power supply
cadcamcenter@y...
2001-10-16 18:42:31 UTC
Re: Members
cadcamcenter@y...
2001-10-16 18:55:21 UTC
Re: power supply
brian
2001-10-16 19:50:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
mariss92705@y...
2001-10-16 19:54:17 UTC
Re: Members
Jon Elson
2001-10-16 20:13:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
Ron Knittle
2001-10-16 21:36:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Members
cncforum
2002-02-03 10:04:42 UTC
power supply
Bob Campbell
2002-02-03 11:56:43 UTC
Re: [CAD_CAM_EDM_DRO] power supply
JanRwl@A...
2002-02-03 12:51:23 UTC
Re: [CAD_CAM_EDM_DRO] power supply
Jon Elson
2002-02-03 22:08:43 UTC
Re: [CAD_CAM_EDM_DRO] power supply
ballendo
2002-02-04 07:52:15 UTC
Ground loops and star wiring was Re: power supply
Raymond Heckert
2002-02-04 14:07:25 UTC
Re: [CAD_CAM_EDM_DRO] power supply
Gene
2002-03-07 22:46:13 UTC
power supply
Mike Snodgrass
2002-09-12 05:42:58 UTC
power supply
turbulatordude
2002-09-12 07:07:48 UTC
Re: power supply
bsptrades
2002-09-12 10:18:00 UTC
Re: power supply
mariss92705
2002-09-12 11:10:36 UTC
Re: power supply
Mike Snodgrass
2002-09-12 16:53:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: power supply
Alan Marconett KM6VV
2002-09-12 17:27:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: power supply
Jon Elson
2002-09-12 22:31:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: power supply
Lee Studley
2002-09-13 10:42:48 UTC
Re: power supply
Yesamazza@a...
2002-12-28 21:25:25 UTC
power supply
Robert Campbell
2002-12-29 06:04:49 UTC
Re: [CAD_CAM_EDM_DRO] power supply
turbulatordude <davemucha@j...
2002-12-29 06:51:13 UTC
Re: power supply
Yesamazza@a...
2002-12-29 09:02:08 UTC
Re: [CAD_CAM_EDM_DRO] power supply
turbulatordude <davemucha@j...
2002-12-29 10:37:56 UTC
Re: power supply
Ron Yost
2002-12-29 11:48:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: power supply
RichD
2002-12-29 13:17:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: power supply
turbulatordude <davemucha@j...
2002-12-29 13:52:49 UTC
Re: power supply
Ron Yost
2002-12-29 14:11:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: power supply
Ron Yost
2002-12-29 14:14:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: power supply
Tim Goldstein
2002-12-29 14:34:13 UTC
RE: [CAD_CAM_EDM_DRO] Re: power supply
afogassa
2003-09-08 18:50:44 UTC
power supply
afogassa
2003-09-10 15:02:44 UTC
power supply
motorworksnf
2004-02-01 14:06:37 UTC
power supply
Doug Fortune
2004-02-01 15:10:07 UTC
Re: [CAD_CAM_EDM_DRO] power supply