CAD CAM EDM DRO - Yahoo Group Archive

Re: power supply

Posted by Lee Studley
on 2002-09-13 10:42:48 UTC
Mike,
I have one as described by Jon. Its yours for $30 plus shipping if
you want it. Its a 1KVA+ 240/208 can be used for 120/104. Heavy
guage wiring. Unused, about 4" cube as described. Its just sitting on
my shelf now. I ended up making an autoformer from some monster
transformers that came with my mill. This one I bought to observe how
they are made. I could have used it in my app, but I'm a glutton for
punishment and had to try hand winding for the experience.

-Lee


--- In CAD_CAM_EDM_DRO@y..., Jon Elson <elson@p...> wrote:
> Mike Snodgrass wrote:
>
> > Bummer! it seemed like a good one. Is there another way to trim
the
> > voltage other than huge , hot, nasty, power resistors or bulky
variac?
>
> Power resistors will not "trim the voltage", either. They will
cause a voltage drop
> that varies with current draw.
>
> There are voltage adjusting transformers (usually autotransformers)
available for
> converting 208 - 240 and 240 - 208. These are often used to run
240 V
> air conditioners, or other mid-size motors, in locatins where
120/208 3-phase
> power is the only thing available. You should be able to find them
at air
> conditioning parts shops and electrical contractor suppliers.
Because the core
> only needs to handle the difference Volt-Amps, these transformers
are quite
> small. About a 4" cube, weighing maybe 6 pounds. I don't think
they are
> expensive. I'll bet Grainger has them, too.
>
> You can cut your voltage to 86% of what it is without the
transformer.
> You'd wire the line input (either 120 or 240 V) to the terminals
marked
> 240 V and the power supply would be connected to the terminals
marked
> 208 V. If you were supplying 120 V to your transformer before, it
would
> now see 104 V. This should help bring your ~80 V down to 69 or so,
> safe for the Gecko.
>
> Jon

Discussion Thread

wanliker@a... 2001-10-14 12:06:43 UTC Members Art Fenerty 2001-10-14 12:51:59 UTC Re: [CAD_CAM_EDM_DRO] Members JanRwl@A... 2001-10-14 13:23:28 UTC Re: [CAD_CAM_EDM_DRO] Members cadcamcenter@y... 2001-10-14 17:38:02 UTC Re: Members Art Fenerty 2001-10-14 18:38:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Members JanRwl@A... 2001-10-14 18:43:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Members Art Fenerty 2001-10-14 19:07:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Members cadcamcenter@y... 2001-10-14 19:19:07 UTC Re: Members Tim Goldstein 2001-10-14 19:57:00 UTC RE: [CAD_CAM_EDM_DRO] Re: Members wanliker@a... 2001-10-14 21:08:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Members cadcamcenter@y... 2001-10-15 06:24:45 UTC Re: Members Tim Goldstein 2001-10-15 07:05:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Members JanRwl@A... 2001-10-15 09:57:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Members Alan Marconett KM6VV 2001-10-15 11:30:33 UTC Re: Members Tim 2001-10-15 12:41:25 UTC RE: [CAD_CAM_EDM_DRO] Re: Members Art Fenerty 2001-10-15 12:45:31 UTC Re: [CAD_CAM_EDM_DRO] Re: Members machines@n... 2001-10-15 13:31:45 UTC Re: Members Art Fenerty 2001-10-15 14:44:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Members Alan Trest 2001-10-15 15:47:26 UTC Re: Members cadcamcenter@y... 2001-10-15 16:30:21 UTC Re: Members Alan Marconett KM6VV 2001-10-15 17:02:57 UTC Re: Members Tom Murray 2001-10-15 18:37:21 UTC Re: Members brian 2001-10-15 19:48:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Members Sven Peter 2001-10-15 20:37:06 UTC Re: [CAD_CAM_EDM_DRO]Members Michael Dhabolt 2001-10-15 20:55:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Members Jon Elson 2001-10-15 22:04:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Members Jon Elson 2001-10-15 22:08:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Members Carol & Jerry Jankura 2001-10-16 06:22:48 UTC RE: [CAD_CAM_EDM_DRO] Re: Members Smoke 2001-10-16 07:10:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Members HighTech 2001-10-16 08:00:31 UTC RE: [CAD_CAM_EDM_DRO] Re: Members Jon Elson 2001-10-16 10:16:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Members Jon Elson 2001-10-16 10:28:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Members Smoke 2001-10-16 10:29:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Members cadcamcenter@y... 2001-10-16 10:31:08 UTC power supply Bob Campbell 2001-10-16 11:00:09 UTC Re: [CAD_CAM_EDM_DRO] power supply Alan Marconett KM6VV 2001-10-16 11:02:42 UTC Re: [CAD_CAM_EDM_DRO] power supply Carol & Jerry Jankura 2001-10-16 11:11:20 UTC RE: [CAD_CAM_EDM_DRO] Re: Members Art Fenerty 2001-10-16 11:18:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Members Les Newell 2001-10-16 12:27:16 UTC Re: [CAD_CAM_EDM_DRO] power supply mariss92705@y... 2001-10-16 13:11:55 UTC Re: Members beer@s... 2001-10-16 13:17:04 UTC Re: Members Paul 2001-10-16 14:39:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Members beer@s... 2001-10-16 15:55:58 UTC Re: power supply JanRwl@A... 2001-10-16 16:37:40 UTC Re: [CAD_CAM_EDM_DRO] power supply cadcamcenter@y... 2001-10-16 16:51:42 UTC Re: power supply mariss92705@y... 2001-10-16 17:26:20 UTC Re: power supply mariss92705@y... 2001-10-16 17:30:24 UTC Re: power supply Alan Marconett KM6VV 2001-10-16 17:36:19 UTC Re: power supply cadcamcenter@y... 2001-10-16 18:42:31 UTC Re: Members cadcamcenter@y... 2001-10-16 18:55:21 UTC Re: power supply brian 2001-10-16 19:50:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Members mariss92705@y... 2001-10-16 19:54:17 UTC Re: Members Jon Elson 2001-10-16 20:13:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Members Ron Knittle 2001-10-16 21:36:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Members cncforum 2002-02-03 10:04:42 UTC power supply Bob Campbell 2002-02-03 11:56:43 UTC Re: [CAD_CAM_EDM_DRO] power supply JanRwl@A... 2002-02-03 12:51:23 UTC Re: [CAD_CAM_EDM_DRO] power supply Jon Elson 2002-02-03 22:08:43 UTC Re: [CAD_CAM_EDM_DRO] power supply ballendo 2002-02-04 07:52:15 UTC Ground loops and star wiring was Re: power supply Raymond Heckert 2002-02-04 14:07:25 UTC Re: [CAD_CAM_EDM_DRO] power supply Gene 2002-03-07 22:46:13 UTC power supply Mike Snodgrass 2002-09-12 05:42:58 UTC power supply turbulatordude 2002-09-12 07:07:48 UTC Re: power supply bsptrades 2002-09-12 10:18:00 UTC Re: power supply mariss92705 2002-09-12 11:10:36 UTC Re: power supply Mike Snodgrass 2002-09-12 16:53:46 UTC Re: [CAD_CAM_EDM_DRO] Re: power supply Alan Marconett KM6VV 2002-09-12 17:27:55 UTC Re: [CAD_CAM_EDM_DRO] Re: power supply Jon Elson 2002-09-12 22:31:29 UTC Re: [CAD_CAM_EDM_DRO] Re: power supply Lee Studley 2002-09-13 10:42:48 UTC Re: power supply Yesamazza@a... 2002-12-28 21:25:25 UTC power supply Robert Campbell 2002-12-29 06:04:49 UTC Re: [CAD_CAM_EDM_DRO] power supply turbulatordude <davemucha@j... 2002-12-29 06:51:13 UTC Re: power supply Yesamazza@a... 2002-12-29 09:02:08 UTC Re: [CAD_CAM_EDM_DRO] power supply turbulatordude <davemucha@j... 2002-12-29 10:37:56 UTC Re: power supply Ron Yost 2002-12-29 11:48:43 UTC Re: [CAD_CAM_EDM_DRO] Re: power supply RichD 2002-12-29 13:17:26 UTC Re: [CAD_CAM_EDM_DRO] Re: power supply turbulatordude <davemucha@j... 2002-12-29 13:52:49 UTC Re: power supply Ron Yost 2002-12-29 14:11:42 UTC Re: [CAD_CAM_EDM_DRO] Re: power supply Ron Yost 2002-12-29 14:14:51 UTC Re: [CAD_CAM_EDM_DRO] Re: power supply Tim Goldstein 2002-12-29 14:34:13 UTC RE: [CAD_CAM_EDM_DRO] Re: power supply afogassa 2003-09-08 18:50:44 UTC power supply afogassa 2003-09-10 15:02:44 UTC power supply motorworksnf 2004-02-01 14:06:37 UTC power supply Doug Fortune 2004-02-01 15:10:07 UTC Re: [CAD_CAM_EDM_DRO] power supply