RE: [CAD_CAM_EDM_DRO] Gecko 201 drive
Posted by
Tim Goldstein
on 2001-12-08 11:27:57 UTC
Sure, just connect a 1/4 watt pot. The drive doesn't know what the resistor
is, only the value. Just be careful when you turn it to not exceed the
capacity of the particular motor.
Tim
[Denver, CO]
is, only the value. Just be careful when you turn it to not exceed the
capacity of the particular motor.
Tim
[Denver, CO]
> -----Original Message-----
>
> How about a multi pole switch with different resistor values for each
> machine?
>
> Just thinking out loud...
> Bryan
>
Discussion Thread
Ron Kline
2001-12-08 07:33:22 UTC
Gecko 201 drive
Art Fenerty
2001-12-08 08:45:44 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive
High Tech
2001-12-08 09:41:19 UTC
RE: [CAD_CAM_EDM_DRO] Gecko 201 drive
Gail & Bryan Harries
2001-12-08 11:12:45 UTC
RE: [CAD_CAM_EDM_DRO] Gecko 201 drive
Tim Goldstein
2001-12-08 11:27:57 UTC
RE: [CAD_CAM_EDM_DRO] Gecko 201 drive
Art Fenerty
2001-12-08 13:46:58 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive
mariss92705
2001-12-08 14:48:35 UTC
Re: Gecko 201 drive
Alan Marconett KM6VV
2001-12-08 15:30:42 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive
High Tech
2001-12-08 16:30:22 UTC
RE: [CAD_CAM_EDM_DRO] Gecko 201 drive
High Tech
2001-12-08 16:40:08 UTC
RE: [CAD_CAM_EDM_DRO] Gecko 201 drive
Gail & Bryan Harries
2001-12-08 16:52:22 UTC
RE: [CAD_CAM_EDM_DRO] Gecko 201 drive
Alan Marconett KM6VV
2001-12-08 17:22:33 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive
Bill Vance
2001-12-08 17:55:57 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive
JanRwl@A...
2001-12-08 18:52:01 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive
Art Fenerty
2001-12-08 18:57:23 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive
JanRwl@A...
2001-12-08 18:59:37 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive
JanRwl@A...
2001-12-08 19:18:03 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive
JanRwl@A...
2001-12-08 19:43:28 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive
Alan Marconett KM6VV
2001-12-08 20:26:15 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive
JanRwl@A...
2001-12-08 20:49:34 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive
Art Fenerty
2001-12-08 20:52:02 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 201 drive