CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Gecko 201 drive

Posted by High Tech
on 2001-12-08 09:41:19 UTC
Art
I think you mean a "shorted" condition not an "open" one. 7 amps on the
gecko is "open" or no resistor or infinite. You would have to ask Mariss
what would happen if you had a "shorted" condition or 0 ohms resistance.
Derek B.
Hi Ron:

A Pot will work , but be warned, pots have a way of going bad and if it
goes open in this application, the controller will let out its magic smoke.
I would advise putting whatever resitance is used for 7 amps in parallel
with the pot so you never get an "open" condition. You just have to use a
large enough resitance in the pot so the combined resistance varies from 0
ohms (low current) to a max of the 7 amp resistance.

Just a thought,
Art
Master5 Software
http://users.andara.com/~fenerty/master.htm

----- Original Message -----
From: "Ron Kline" <ulpilots@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Saturday, December 08, 2001 10:33 AM
Subject: [CAD_CAM_EDM_DRO] Gecko 201 drive


> The 201 uses a 1/4 watt resister to set the output
> current , do any of you know if I could use a pot
> instead so I can change the out put when I'm using the
> drivers on my other machines .
> Thanks
> Ron K
>
> __________________________________________________

Discussion Thread

Ron Kline 2001-12-08 07:33:22 UTC Gecko 201 drive Art Fenerty 2001-12-08 08:45:44 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive High Tech 2001-12-08 09:41:19 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Gail & Bryan Harries 2001-12-08 11:12:45 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Tim Goldstein 2001-12-08 11:27:57 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Art Fenerty 2001-12-08 13:46:58 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive mariss92705 2001-12-08 14:48:35 UTC Re: Gecko 201 drive Alan Marconett KM6VV 2001-12-08 15:30:42 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive High Tech 2001-12-08 16:30:22 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive High Tech 2001-12-08 16:40:08 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Gail & Bryan Harries 2001-12-08 16:52:22 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Alan Marconett KM6VV 2001-12-08 17:22:33 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive Bill Vance 2001-12-08 17:55:57 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 18:52:01 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive Art Fenerty 2001-12-08 18:57:23 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 18:59:37 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 19:18:03 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 19:43:28 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive Alan Marconett KM6VV 2001-12-08 20:26:15 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 20:49:34 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive Art Fenerty 2001-12-08 20:52:02 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive