CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Gecko 201 drive

on 2001-12-08 17:22:33 UTC
Hi Ron,

Yes, that's what I had in mind. Although the combination of Mariss'
regulated reference, and a switch would be even more to my liking.
Actually, I wonder if we couldn't use a Dallas Semiconductor
programmable pot (or a similar approach), and allow a default low
current, and a programmable current level from the controller program!

Alan KM6VV


High Tech wrote:
>
> Alan
> You would still have to be careful with a switch because
> it will open up in between your resistor positions and go
> straight to 7amp output. That is a break before make switch
> their maybe a way around this or use Mariss's idea since he
> did design the Gecko drives.
> Derek
>
> Hi Ron,
>
> I'd be more inclined to use a multi-position switch.
>
> Alan KM6VV
>
> Ron Kline wrote:
> >
> > The 201 uses a 1/4 watt resister to set the output
> > current , do any of you know if I could use a pot
> > instead so I can change the out put when I'm using the
> > drivers on my other machines .
> > Thanks
> > Ron K

Discussion Thread

Ron Kline 2001-12-08 07:33:22 UTC Gecko 201 drive Art Fenerty 2001-12-08 08:45:44 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive High Tech 2001-12-08 09:41:19 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Gail & Bryan Harries 2001-12-08 11:12:45 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Tim Goldstein 2001-12-08 11:27:57 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Art Fenerty 2001-12-08 13:46:58 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive mariss92705 2001-12-08 14:48:35 UTC Re: Gecko 201 drive Alan Marconett KM6VV 2001-12-08 15:30:42 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive High Tech 2001-12-08 16:30:22 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive High Tech 2001-12-08 16:40:08 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Gail & Bryan Harries 2001-12-08 16:52:22 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Alan Marconett KM6VV 2001-12-08 17:22:33 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive Bill Vance 2001-12-08 17:55:57 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 18:52:01 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive Art Fenerty 2001-12-08 18:57:23 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 18:59:37 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 19:18:03 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 19:43:28 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive Alan Marconett KM6VV 2001-12-08 20:26:15 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 20:49:34 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive Art Fenerty 2001-12-08 20:52:02 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive