CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Gecko 201 drive

Posted by High Tech
on 2001-12-08 16:30:22 UTC
Alan
You would still have to be careful with a switch because
it will open up in between your resistor positions and go
straight to 7amp output. That is a break before make switch
their maybe a way around this or use Mariss's idea since he
did design the Gecko drives.
Derek

Hi Ron,

I'd be more inclined to use a multi-position switch.

Alan KM6VV


Ron Kline wrote:
>
> The 201 uses a 1/4 watt resister to set the output
> current , do any of you know if I could use a pot
> instead so I can change the out put when I'm using the
> drivers on my other machines .
> Thanks
> Ron K


Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

Ron Kline 2001-12-08 07:33:22 UTC Gecko 201 drive Art Fenerty 2001-12-08 08:45:44 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive High Tech 2001-12-08 09:41:19 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Gail & Bryan Harries 2001-12-08 11:12:45 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Tim Goldstein 2001-12-08 11:27:57 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Art Fenerty 2001-12-08 13:46:58 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive mariss92705 2001-12-08 14:48:35 UTC Re: Gecko 201 drive Alan Marconett KM6VV 2001-12-08 15:30:42 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive High Tech 2001-12-08 16:30:22 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive High Tech 2001-12-08 16:40:08 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Gail & Bryan Harries 2001-12-08 16:52:22 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201 drive Alan Marconett KM6VV 2001-12-08 17:22:33 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive Bill Vance 2001-12-08 17:55:57 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 18:52:01 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive Art Fenerty 2001-12-08 18:57:23 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 18:59:37 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 19:18:03 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 19:43:28 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive Alan Marconett KM6VV 2001-12-08 20:26:15 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive JanRwl@A... 2001-12-08 20:49:34 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive Art Fenerty 2001-12-08 20:52:02 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201 drive