Re: [CAD_CAM_EDM_DRO] help with g201 needed
Posted by
Al Schoepp
on 2002-01-13 16:13:01 UTC
Bill,
I swapped the output to the motor
Al
At 06:21 PM 13/01/2002 -0500, you wrote:
I swapped the output to the motor
Al
At 06:21 PM 13/01/2002 -0500, you wrote:
>Al,[Non-text portions of this message have been removed]
>
>When you say you swapped the cable, did you swap the input to
>the drive or the output to the motor. If you swapped the input then it
>sounds like the wire that sends the direction signal to the drive
>has opened on that axis.
>
>Bill
>
> > Hi, hope someone here can help. I've got a Taig micromill converted to
>CNC
> > with 3 G201A's using CNCpro. It was working well before Christmas. I get
> > back from holidays and tried to do some work on it and the Z axis only
>goes
> > up, it doesn't matter which direction I try to move it. I swapped the
> > cable with the X axis and then the X axis would only go one direction no
> > matter which direction I wanted it to move while the Z axis now works
> > correctly. I did no changes, or even had anything open since the last
>time
> > I successfully used it. Any suggestions?
> >
> > Thanks,
> > Al
> >
> >
> > [Non-text portions of this message have been removed]
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> >
> > Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> > Moderator: jmelson@... timg@... [Moderator]
> > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > bill,
> > List Manager
> >
> >
> >
> > Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
> >
> >
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
>Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
Al Schoepp
2002-01-13 14:35:48 UTC
help with g201 needed
William Scalione
2002-01-13 15:21:38 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-13 16:13:01 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Doug Harrison
2002-01-13 16:44:43 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-13 17:11:34 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
mariss92705
2002-01-13 21:44:51 UTC
Re: help with g201 needed
Jon Elson
2002-01-13 22:47:47 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-14 06:30:28 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-14 06:33:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed
Alan Marconett KM6VV
2002-01-14 10:26:30 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
quantilas
2002-01-14 17:27:18 UTC
Re: help with g201 needed
Alan Marconett KM6VV
2002-01-14 18:00:09 UTC
Re: help with g201 needed
Al Schoepp
2002-01-19 08:10:59 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-19 08:11:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed
Alan Marconett KM6VV
2002-01-19 13:08:24 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
edwinmylee
2002-01-19 13:51:03 UTC
Re: help with g201 needed
Al Schoepp
2002-01-19 15:15:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed
Al Schoepp
2002-01-19 15:18:41 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Jon Elson
2002-01-19 21:58:12 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-20 05:50:15 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Alan Marconett KM6VV
2002-01-20 14:42:33 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Jon Elson
2002-01-20 22:15:08 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
mariss92705
2002-01-21 11:28:17 UTC
Re: help with g201 needed
Jon Elson
2002-01-21 23:03:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed
Fitch R. Williams
2002-01-22 06:08:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed