Re: [CAD_CAM_EDM_DRO] help with g201 needed
Posted by
Doug Harrison
on 2002-01-13 16:44:43 UTC
Sounds like your direction input to the gecko is dead. You should get about
5V in one direction and maybe 1V in the other direction. If it doesn't
change after a direction change then you have a problem with the parallel
port.
Doug
Z axis only goes
5V in one direction and maybe 1V in the other direction. If it doesn't
change after a direction change then you have a problem with the parallel
port.
Doug
Z axis only goes
> up, it doesn't matter which direction I try to move it. I swapped thetime
> cable with the X axis and then the X axis would only go one direction no
> matter which direction I wanted it to move while the Z axis now works
> correctly. I did no changes, or even had anything open since the last
> I successfully used it. Any suggestions?
>
> Thanks,
> Al
Discussion Thread
Al Schoepp
2002-01-13 14:35:48 UTC
help with g201 needed
William Scalione
2002-01-13 15:21:38 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-13 16:13:01 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Doug Harrison
2002-01-13 16:44:43 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-13 17:11:34 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
mariss92705
2002-01-13 21:44:51 UTC
Re: help with g201 needed
Jon Elson
2002-01-13 22:47:47 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-14 06:30:28 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-14 06:33:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed
Alan Marconett KM6VV
2002-01-14 10:26:30 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
quantilas
2002-01-14 17:27:18 UTC
Re: help with g201 needed
Alan Marconett KM6VV
2002-01-14 18:00:09 UTC
Re: help with g201 needed
Al Schoepp
2002-01-19 08:10:59 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-19 08:11:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed
Alan Marconett KM6VV
2002-01-19 13:08:24 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
edwinmylee
2002-01-19 13:51:03 UTC
Re: help with g201 needed
Al Schoepp
2002-01-19 15:15:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed
Al Schoepp
2002-01-19 15:18:41 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Jon Elson
2002-01-19 21:58:12 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-20 05:50:15 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Alan Marconett KM6VV
2002-01-20 14:42:33 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Jon Elson
2002-01-20 22:15:08 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
mariss92705
2002-01-21 11:28:17 UTC
Re: help with g201 needed
Jon Elson
2002-01-21 23:03:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed
Fitch R. Williams
2002-01-22 06:08:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed