Re: help with g201 needed
Posted by
Alan Marconett KM6VV
on 2002-01-14 18:00:09 UTC
Hi Al, Joe,
Yes, that's a pretty good reason! I hadn't heard of 3.3v I/O's! How
about getting a 5V I/O? Or perhaps a parallel port buffer, if that's
the problem. Still, the +5V supplied to the Gecko (common) need to be
driven from POWER, not just stealing voltage from a parallel port line,
like a dongle! The G201A's want to SINK current.
If 3.5V works, and 3.3V doesn't, does that mean you've got LESS then
about 0.2V of noise immunity?? These low voltages don't give the noise
immunity that a good 4.5V signal swing will give, IMO.
Alan KM6VV
quantilas wrote:
Yes, that's a pretty good reason! I hadn't heard of 3.3v I/O's! How
about getting a 5V I/O? Or perhaps a parallel port buffer, if that's
the problem. Still, the +5V supplied to the Gecko (common) need to be
driven from POWER, not just stealing voltage from a parallel port line,
like a dongle! The G201A's want to SINK current.
If 3.5V works, and 3.3V doesn't, does that mean you've got LESS then
about 0.2V of noise immunity?? These low voltages don't give the noise
immunity that a good 4.5V signal swing will give, IMO.
Alan KM6VV
quantilas wrote:
>
> I had the same problem at one point. I increased the MB IO voltage
> from 3.3v to 3.5 volts and that pesky Z axis ran smoother and ran in
> both directions. If you have this option in your bios it may help
> get that little extra current I think you need to sync the optos.
>
> Regards
> Joe
>
> --- In CAD_CAM_EDM_DRO@y..., Alan Marconett KM6VV <KM6VV@a...> wrote:
> > Hi Al,
> >
> > Sounds like the Gecko's are not getting +5V; they are "stealing"
> it from
> > the direction line! What is your +5V supply?
> >
> > HTH
> >
> > Alan KM6VV
> >
> >
> > Al Schoepp wrote:
> > >
> > > Hi, hope someone here can help. I've got a Taig micromill
> converted to CNC
> > > with 3 G201A's using CNCpro. It was working well before
> Christmas. I get
> > > back from holidays and tried to do some work on it and the Z
> axis only goes
> > > up, it doesn't matter which direction I try to move it. I
> swapped the
> > > cable with the X axis and then the X axis would only go one
> direction no
> > > matter which direction I wanted it to move while the Z axis now
> works
> > > correctly. I did no changes, or even had anything open since
> the last time
> > > I successfully used it. Any suggestions?
> > >
> > > Thanks,
> > > Al
Discussion Thread
Al Schoepp
2002-01-13 14:35:48 UTC
help with g201 needed
William Scalione
2002-01-13 15:21:38 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-13 16:13:01 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Doug Harrison
2002-01-13 16:44:43 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-13 17:11:34 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
mariss92705
2002-01-13 21:44:51 UTC
Re: help with g201 needed
Jon Elson
2002-01-13 22:47:47 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-14 06:30:28 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-14 06:33:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed
Alan Marconett KM6VV
2002-01-14 10:26:30 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
quantilas
2002-01-14 17:27:18 UTC
Re: help with g201 needed
Alan Marconett KM6VV
2002-01-14 18:00:09 UTC
Re: help with g201 needed
Al Schoepp
2002-01-19 08:10:59 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-19 08:11:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed
Alan Marconett KM6VV
2002-01-19 13:08:24 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
edwinmylee
2002-01-19 13:51:03 UTC
Re: help with g201 needed
Al Schoepp
2002-01-19 15:15:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed
Al Schoepp
2002-01-19 15:18:41 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Jon Elson
2002-01-19 21:58:12 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Al Schoepp
2002-01-20 05:50:15 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Alan Marconett KM6VV
2002-01-20 14:42:33 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
Jon Elson
2002-01-20 22:15:08 UTC
Re: [CAD_CAM_EDM_DRO] help with g201 needed
mariss92705
2002-01-21 11:28:17 UTC
Re: help with g201 needed
Jon Elson
2002-01-21 23:03:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed
Fitch R. Williams
2002-01-22 06:08:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed