CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] help with g201 needed

Posted by Al Schoepp
on 2002-01-13 17:11:34 UTC
Unfortunately I just swapped the Z axis drive to the Y axis and the problem
follows it. :) I've sent an email to Mariss asking for his help to see
what I've done.

Al

At 07:49 PM 13/01/2002 -0500, you wrote:
>Sounds like your direction input to the gecko is dead. You should get about
>5V in one direction and maybe 1V in the other direction. If it doesn't
>change after a direction change then you have a problem with the parallel
>port.
>
>Doug
>
>
>Z axis only goes
> > up, it doesn't matter which direction I try to move it. I swapped the
> > cable with the X axis and then the X axis would only go one direction no
> > matter which direction I wanted it to move while the Z axis now works
> > correctly. I did no changes, or even had anything open since the last
>time
> > I successfully used it. Any suggestions?
> >
> > Thanks,
> > Al
>
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
>Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/


[Non-text portions of this message have been removed]

Discussion Thread

Al Schoepp 2002-01-13 14:35:48 UTC help with g201 needed William Scalione 2002-01-13 15:21:38 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed Al Schoepp 2002-01-13 16:13:01 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed Doug Harrison 2002-01-13 16:44:43 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed Al Schoepp 2002-01-13 17:11:34 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed mariss92705 2002-01-13 21:44:51 UTC Re: help with g201 needed Jon Elson 2002-01-13 22:47:47 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed Al Schoepp 2002-01-14 06:30:28 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed Al Schoepp 2002-01-14 06:33:30 UTC Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed Alan Marconett KM6VV 2002-01-14 10:26:30 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed quantilas 2002-01-14 17:27:18 UTC Re: help with g201 needed Alan Marconett KM6VV 2002-01-14 18:00:09 UTC Re: help with g201 needed Al Schoepp 2002-01-19 08:10:59 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed Al Schoepp 2002-01-19 08:11:36 UTC Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed Alan Marconett KM6VV 2002-01-19 13:08:24 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed edwinmylee 2002-01-19 13:51:03 UTC Re: help with g201 needed Al Schoepp 2002-01-19 15:15:37 UTC Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed Al Schoepp 2002-01-19 15:18:41 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed Jon Elson 2002-01-19 21:58:12 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed Al Schoepp 2002-01-20 05:50:15 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed Alan Marconett KM6VV 2002-01-20 14:42:33 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed Jon Elson 2002-01-20 22:15:08 UTC Re: [CAD_CAM_EDM_DRO] help with g201 needed mariss92705 2002-01-21 11:28:17 UTC Re: help with g201 needed Jon Elson 2002-01-21 23:03:41 UTC Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed Fitch R. Williams 2002-01-22 06:08:49 UTC Re: [CAD_CAM_EDM_DRO] Re: help with g201 needed