Re: [CAD_CAM_EDM_DRO] Re: I want to upgrade to servors
Posted by
Jon Elson
on 2002-02-14 22:53:25 UTC
luisguillermo98 wrote:
the step/direction input servo drives. The Gecko drives seem to be
a good choice.
If you want to change software, then there are several options. I
prefer EMC, it seems the most flexible. You can use a Servo-to-Go
card or my Parallel Port Motion Control cards. You will also need
encoders and servo amps. Sometimes these come up on eBay for
a good price.
Jon
> I am using turboCNC for software,250 oz 4v 2amp steppers brandWithout changing software, you are pretty much forced to go with
> eastern air device and the camtronic controller.. I have tried
> several settings like min speed, max speed and I could not getting
> faster.. the steppers locking up or loose step if I run it faster
> tried other softwares and nothing better so I decided to go for
> servo.. any suggestions??
the step/direction input servo drives. The Gecko drives seem to be
a good choice.
If you want to change software, then there are several options. I
prefer EMC, it seems the most flexible. You can use a Servo-to-Go
card or my Parallel Port Motion Control cards. You will also need
encoders and servo amps. Sometimes these come up on eBay for
a good price.
Jon
Discussion Thread
luisguillermo98
2002-02-12 16:15:17 UTC
I want to upgrade to servors
Jon Elson
2002-02-12 20:37:31 UTC
Re: [CAD_CAM_EDM_DRO] I want to upgrade to servors
luisguillermo98
2002-02-13 20:05:18 UTC
Re: I want to upgrade to servors
Jon Elson
2002-02-13 23:16:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: I want to upgrade to servors
ballendo
2002-02-14 03:55:37 UTC
Re: I want to upgrade to servors
luisguillermo98
2002-02-14 13:22:17 UTC
Re: I want to upgrade to servors
luisguillermo98
2002-02-14 13:27:26 UTC
Re: I want to upgrade to servors
Carol & Jerry Jankura
2002-02-14 14:06:19 UTC
RE: [CAD_CAM_EDM_DRO] Re: I want to upgrade to servors
Jon Elson
2002-02-14 22:53:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: I want to upgrade to servors
luisguillermo98
2002-02-15 20:30:04 UTC
Re: I want to upgrade to servors
Carol & Jerry Jankura
2002-02-15 22:06:23 UTC
RE: [CAD_CAM_EDM_DRO] Re: I want to upgrade to servors
ballendo
2002-02-16 01:39:45 UTC
Re: I want to upgrade to servors
Michael Milligan
2002-02-16 02:16:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: I want to upgrade to servors/ EMM386.EXE
Carol & Jerry Jankura
2002-02-16 05:37:32 UTC
RE: [CAD_CAM_EDM_DRO] Re: I want to upgrade to servors/ EMM386.EXE
luisguillermo98
2002-02-16 08:06:59 UTC
Re: I want to upgrade to servors/ EMM386.EXE
dave_ace_me
2002-02-16 09:18:02 UTC
Re: I want to upgrade to servors/ EMM386.EXE
Carol & Jerry Jankura
2002-02-16 10:52:04 UTC
RE: [CAD_CAM_EDM_DRO] Re: I want to upgrade to servors/ EMM386.EXE
Carol & Jerry Jankura
2002-02-16 10:56:30 UTC
RE: [CAD_CAM_EDM_DRO] Re: I want to upgrade to servors/ EMM386.EXE
luisguillermo98
2002-02-17 11:39:35 UTC
Re: I want to upgrade to servors/ EMM386.EXE
luisguillermo98
2002-02-17 11:41:00 UTC
Re: I want to upgrade to servors/ EMM386.EXE
luisguillermo98
2002-02-17 11:45:46 UTC
Re: I want to upgrade to servors/ EMM386.EXE
luisguillermo98
2002-02-17 12:31:31 UTC
Re: I want to upgrade to servors
dkowalcz2000
2002-02-17 19:18:04 UTC
Re: I want to upgrade to servors/ EMM386.EXE
ballendo
2002-02-18 01:03:19 UTC
Re: I want to upgrade to servors
luisguillermo98
2002-02-19 16:25:14 UTC
Re: I want to upgrade to servors
ballendo
2002-02-20 07:19:54 UTC
Re: I want to upgrade to servors