CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors

on 2002-04-12 10:47:31 UTC
These bellows type are round and would work nice, they arn't as expensive
as the ones you mentioned. Onother option would be to use pure rubber vacum
cleaner hose, available from janitorial supply, or a hose like clothes
dryer hose if you can find some that small O.D.






----- Original Message -----
From: "dave_ace_me" <davemucha@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Friday, April 12, 2002 10:34 AM
Subject: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping
leadscrew protectors


> I agree, some parts of this business is just womens work. :" )
>
> I looked at using a self winding roll to be uded to keep the chips
> away but that was a flat top and would actually hold the small chips
> until it would pass some sort of angle to let them fall.
>
> My chips are cold, so plastic or rubber would work but I did not like
> the cost of the rubber bellows. I tried to find some from a TV Dish
> style linear actuator, nice length, but they seem to range around
> $20.00 a foot for the stuff.
>
> I opted for what I had on hand and may still switch to an inverted V
> for the simplicity and also access.
>
> Dave
>
>
>
>
>
> --- In CAD_CAM_EDM_DRO@y..., "Mike Snodgrass" <snarf@s...> wrote:
> >
> > ----- Original Message -----
> > From: "Sven Peter" <peteryco@r...>
> > To: <CAD_CAM_EDM_DRO@y...>
> > Sent: Friday, April 12, 2002 7:11 AM
> > Subject: Re: [CAD_CAM_EDM_DRO] telescoping leadscrew protectors
> >
> > I have, and I know you can get long " bellows" type protectors in
> many
> > sizes. They are used to protect hydraulic cylinder shafts, I
> think they
> > are expensive though it would be easy for a woman with a sewing
> machine and
> > some good apolstery material. You can get the new ones from a
> hydraulic
> > dealer.
> >
> >
> >
> >
> >
> > > Hello Doug,
> > > You can put tubing together but travel might pet reduced.
> > > Kabelschlepp and others sell cylindrical springs.
> > > "Steel, Hilton" <HSteel@k...>
> > > You might be able to make some out of very wide packing steel
> band like
> > > for
> > > transport boxes. But I tell you ITS NASTY. I had to do something
> > > simmilar for
> > > to substitute drill press springs. Therefor I prefer to buy the
> stuff.
> > > Good luck
> > > Sven Peter
> > >
> > > Doug Fortune wrote:
> > > >
> > > > dave_ace_me wrote:
> > > >
> > > > > btw, on my table, I am using a single lead screw, under the
> table,
> > > > > with telescoping tubing as protection. This is very simple
> and well
> > > > > worth the effort to keep chips clear.
> > > >
> > > > Hi Dave:
> > > >
> > > > I'd be interesting in hearing more about how you made those
> > > > telescoping tubes. I think Reid sells nested sets of aluminum
> > > > tubes, but how do you get them to not pull completely apart?
> > > >
> > > > Doug Fortune
> > > > http://www.cncKITS.com NEW -> 1KW power supply kits
> > > >
> > > > Addresses:
> > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > >
> > > > OFF Topic POSTS: General Machining
> > > > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> reach it if
> > you have trouble.
> > > > http://www.metalworking.com/news_servers.html
> > > >
> > > > http://groups.yahoo.com/group/jobshophomeshop I consider this
> as a
> > sister site to the CCED group, as many of the same memembers are
> there, for
> > OT subjects, that are not allowed on the CCED list.
> > > >
> > > > Post messages: CAD_CAM_EDM_DRO@y...
> > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > > > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > > > Moderator: jmelson@a... timg@k... [Moderator]
> > > > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > > bill,
> > > > List Mom
> > > > List Owner
> > > >
> > > >
> > > >
> > > > Your use of Yahoo! Groups is subject to
> > http://docs.yahoo.com/info/terms/
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > >
> > > OFF Topic POSTS: General Machining
> > > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> reach it if
> > you have trouble.
> > > http://www.metalworking.com/news_servers.html
> > >
> > > http://groups.yahoo.com/group/jobshophomeshop I consider this
> as a
> > sister site to the CCED group, as many of the same memembers are
> there, for
> > OT subjects, that are not allowed on the CCED list.
> > >
> > >
> > >
> > > Post messages: CAD_CAM_EDM_DRO@y...
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > > Moderator: jmelson@a... timg@k... [Moderator]
> > > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > bill,
> > > List Mom
> > > List Owner
> > >
> > >
> > >
> > > Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
> > >
> > >
> > >
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same memembers are there, for
OT subjects, that are not allowed on the CCED list.
>
>
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>

Discussion Thread

Doug Fortune 2002-04-11 22:21:23 UTC telescoping leadscrew protectors dave_ace_me 2002-04-12 05:22:39 UTC Re: telescoping leadscrew protectors Sven Peter 2002-04-12 07:07:34 UTC Re: [CAD_CAM_EDM_DRO] telescoping leadscrew protectors Mike Snodgrass 2002-04-12 08:58:05 UTC Re: [CAD_CAM_EDM_DRO] telescoping leadscrew protectors rsgoldner 2002-04-12 09:33:33 UTC Re: telescoping leadscrew protectors dave_ace_me 2002-04-12 09:57:46 UTC leadscrew protectors ( was Re: telescoping leadscrew protectors Alan Marconett KM6VV 2002-04-12 10:33:09 UTC Re: [CAD_CAM_EDM_DRO] telescoping leadscrew protectors Mike Snodgrass 2002-04-12 10:47:31 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors Jon Elson 2002-04-12 11:12:47 UTC Re: [CAD_CAM_EDM_DRO] telescoping leadscrew protectors Jon Elson 2002-04-12 11:15:03 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors studleylee 2002-04-12 15:17:51 UTC leadscrew protectors ( was Re: telescoping leadscrew protectors Jerry Biehler 2002-04-12 16:51:05 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors Brian Pitt 2002-04-12 20:23:02 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors Brian Pitt 2002-04-12 20:37:35 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors Paul Weber 2002-04-12 22:35:29 UTC Re: [CAD_CAM_EDM_DRO] telescoping leadscrew protectors Jon Elson 2002-04-12 22:35:55 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors Tom Kahara 2002-04-13 12:38:30 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors ballendo 2002-04-15 05:55:08 UTC leadscrew protectors ( was Re: telescoping leadscrew protectors ballendo 2002-04-15 06:27:35 UTC more leadscrew protectors ( was Re: telescoping leadscrew protectors Peter 2002-04-15 07:49:23 UTC Re: [CAD_CAM_EDM_DRO] more leadscrew protectors ( was Re: telescoping leadscrew protectors Alan Marconett KM6VV 2002-04-15 11:12:15 UTC Re: [CAD_CAM_EDM_DRO] more leadscrew protectors ( was Re: telescoping leadscrew protectors aspaguy 2002-04-15 21:17:28 UTC leadscrew protectors ( was Re: telescoping leadscrew protectors dave_ace_me 2002-04-16 13:48:33 UTC leadscrew protectors ( was Re: telescoping leadscrew protectors Jon Elson 2002-04-16 23:43:44 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors ballendo 2002-04-17 02:19:48 UTC leadscrew protectors ( was Re: telescoping leadscrew protectors