CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO]floating z axis

Posted by Bill Vance
on 2002-05-23 13:34:02 UTC
On Thu May 23 12:10:50 2002, wanliker@..., <wanliker@...> wrote:

>You also might consider a vacuum table to hold the board flat, might be
>easier.......
>With stops on the sides and ends
>bill

Hi Bill;

You could also get some tubing sized to make a sleeve around the tool, Drill
and tap it to hold it to the tool, round the end where X amount of the tool is
allowed to extend out, polish it smooth so as not to tear up the traces, and
just use sleeve pressure to hold the PCB flat at the cutting location. The
actual cutting location would be the only place that actually needs to be held
flat at any time.

Bill

--
----------------------------------------------------------------------------
RKBA! ***** Blessings On Thee, Oh Israel! ***** 4-19!
----------------+----------+--------------------------+---------------------
An _EFFECTIVE_ | Insured | All matter is vibration. | Let he who hath no
weapon in every | by COLT; | -- Max Plank | weapon sell his
hand = Freedom | DIAL | In the beginning was the | garment and buy a
on every side! | 1911-A1. | word. -- The Bible | sword.--Jesus Christ
----------------+----------+--------------------------+---------------------

Constitutional Government is dead, LONG LIVE THE CONSTITUTION!!!!!

----------------------------------------------------------------------------

Discussion Thread

pleijnen 2002-05-23 08:54:03 UTC DeskWinNC vs Flashcut? Tim Goldstein 2002-05-23 09:05:25 UTC Re: [CAD_CAM_EDM_DRO] DeskWinNC vs Flashcut? Jim Avey 2002-05-23 10:32:50 UTC RE: [CAD_CAM_EDM_DRO]floating z axis JanRwl@A... 2002-05-23 12:08:45 UTC Re: [CAD_CAM_EDM_DRO]floating z axis JanRwl@A... 2002-05-23 12:10:14 UTC Re: [CAD_CAM_EDM_DRO]floating z axis wanliker@a... 2002-05-23 12:10:57 UTC Re: [CAD_CAM_EDM_DRO]floating z axis bwrfromuk 2002-05-23 12:40:34 UTC Re: [CAD_CAM_EDM_DRO]floating z axis JanRwl@A... 2002-05-23 12:50:07 UTC Re: [CAD_CAM_EDM_DRO]floating z axis Bill Vance 2002-05-23 13:34:02 UTC Re: [CAD_CAM_EDM_DRO]floating z axis Jim Avey 2002-05-23 13:34:39 UTC RE: [CAD_CAM_EDM_DRO]floating z axis Les Newell 2002-05-23 14:20:08 UTC Re: [CAD_CAM_EDM_DRO]floating z axis Jim Avey 2002-05-23 14:34:54 UTC RE: [CAD_CAM_EDM_DRO]floating z axis William Scalione 2002-05-23 16:09:42 UTC Re: [CAD_CAM_EDM_DRO]floating z axis waynegramlich 2002-05-23 16:34:01 UTC Re: [CAD_CAM_EDM_DRO]floating z axis turbulatordude 2002-05-23 18:31:46 UTC Re: [CAD_CAM_EDM_DRO]floating z axis JanRwl@A... 2002-05-23 19:00:13 UTC Re: [CAD_CAM_EDM_DRO]floating z axis aspaguy 2002-05-23 19:50:18 UTC Re: DeskWinNC vs Flashcut? Chris L 2002-05-23 20:37:35 UTC Re: [CAD_CAM_EDM_DRO] Re: DeskWinNC vs Flashcut? Chris L 2002-05-23 20:56:01 UTC Re: [CAD_CAM_EDM_DRO]floating z axis Jon Elson 2002-05-23 21:40:49 UTC Re: [CAD_CAM_EDM_DRO]floating z axis Nic van der Walt 2002-05-24 01:11:49 UTC RE: [CAD_CAM_EDM_DRO]floating z axis bjammin@i... 2002-05-24 05:05:05 UTC tape, babay bjammin@i... 2002-05-24 05:09:38 UTC Re: [CAD_CAM_EDM_DRO]floating z axis bwrfromuk 2002-05-24 08:29:10 UTC Re: [CAD_CAM_EDM_DRO]floating z axis JanRwl@A... 2002-05-24 08:49:33 UTC Re: [CAD_CAM_EDM_DRO] tape, babay JanRwl@A... 2002-05-24 08:53:20 UTC Re: [CAD_CAM_EDM_DRO]floating z axis reed_irion 2002-05-24 10:25:09 UTC Re: [CAD_CAM_EDM_DRO]floating z axis Alan Marconett KM6VV 2002-05-24 11:06:02 UTC Re: [CAD_CAM_EDM_DRO]floating z axis Nic van der Walt 2002-05-24 11:56:58 UTC RE: [CAD_CAM_EDM_DRO]floating z axis Alan Marconett KM6VV 2002-05-24 12:51:11 UTC Re: [CAD_CAM_EDM_DRO]floating z axis Alan Marconett KM6VV 2002-05-24 13:31:05 UTC Re: [CAD_CAM_EDM_DRO]floating z axis bjammin@i... 2002-05-24 15:25:13 UTC Re: [CAD_CAM_EDM_DRO] tape, babay