Re: [CAD_CAM_EDM_DRO]floating z axis
Posted by
Alan Marconett KM6VV
on 2002-05-24 13:31:05 UTC
Hi Nic,
OK, now I see what isolation you're talking about, "Electrical
Isolation", as you were at one point using an electrical sensor to
detect the board. I was fixated on the mechanical approach to sensing
the board. Yes, that would require an entirely different ordering!
Alan KM6VV
Nic van der Walt wrote:
OK, now I see what isolation you're talking about, "Electrical
Isolation", as you were at one point using an electrical sensor to
detect the board. I was fixated on the mechanical approach to sensing
the board. Yes, that would require an entirely different ordering!
Alan KM6VV
Nic van der Walt wrote:
>
> >That's an interesting approach to cutting a board! I'm not quite sure
> >what you meant by your statement "if you get islands...aviod isolation
> >problems...reorder".
>
> If you cut the tracks on the outside of the board first you could create
> areas of copper that you still have to route, but that aren't connected
> to the ground wire anymore.
> <SNIP>
> N.
Discussion Thread
pleijnen
2002-05-23 08:54:03 UTC
DeskWinNC vs Flashcut?
Tim Goldstein
2002-05-23 09:05:25 UTC
Re: [CAD_CAM_EDM_DRO] DeskWinNC vs Flashcut?
Jim Avey
2002-05-23 10:32:50 UTC
RE: [CAD_CAM_EDM_DRO]floating z axis
JanRwl@A...
2002-05-23 12:08:45 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
JanRwl@A...
2002-05-23 12:10:14 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
wanliker@a...
2002-05-23 12:10:57 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
bwrfromuk
2002-05-23 12:40:34 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
JanRwl@A...
2002-05-23 12:50:07 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Bill Vance
2002-05-23 13:34:02 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Jim Avey
2002-05-23 13:34:39 UTC
RE: [CAD_CAM_EDM_DRO]floating z axis
Les Newell
2002-05-23 14:20:08 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Jim Avey
2002-05-23 14:34:54 UTC
RE: [CAD_CAM_EDM_DRO]floating z axis
William Scalione
2002-05-23 16:09:42 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
waynegramlich
2002-05-23 16:34:01 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
turbulatordude
2002-05-23 18:31:46 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
JanRwl@A...
2002-05-23 19:00:13 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
aspaguy
2002-05-23 19:50:18 UTC
Re: DeskWinNC vs Flashcut?
Chris L
2002-05-23 20:37:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: DeskWinNC vs Flashcut?
Chris L
2002-05-23 20:56:01 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Jon Elson
2002-05-23 21:40:49 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Nic van der Walt
2002-05-24 01:11:49 UTC
RE: [CAD_CAM_EDM_DRO]floating z axis
bjammin@i...
2002-05-24 05:05:05 UTC
tape, babay
bjammin@i...
2002-05-24 05:09:38 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
bwrfromuk
2002-05-24 08:29:10 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
JanRwl@A...
2002-05-24 08:49:33 UTC
Re: [CAD_CAM_EDM_DRO] tape, babay
JanRwl@A...
2002-05-24 08:53:20 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
reed_irion
2002-05-24 10:25:09 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Alan Marconett KM6VV
2002-05-24 11:06:02 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Nic van der Walt
2002-05-24 11:56:58 UTC
RE: [CAD_CAM_EDM_DRO]floating z axis
Alan Marconett KM6VV
2002-05-24 12:51:11 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Alan Marconett KM6VV
2002-05-24 13:31:05 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
bjammin@i...
2002-05-24 15:25:13 UTC
Re: [CAD_CAM_EDM_DRO] tape, babay