tape, babay
Posted by
bjammin@i...
on 2002-05-24 05:05:05 UTC
At 10:00 PM 5/23/02 EDT, you wrote:
steel part 2" thick to the faceplate of a big Heald Red Head ID/OD grinder.
I told them if that part came off over a 12,000 RPM ID spindle, it would
kill somebody. And indeed the trial piece shifted alarmingly easily under
hand pressure. I flat refused the job, and they went to sequential clamping
first on OD and then on ID, to do both in one setup. Whew.
Regards, Hoyt
Anti-virus request: Please do not add this email addy to address books
Belfab CNC - http://www.freeyellow.com/members/belfab/belfab.html
US Best MC - http://www.freeyellow.com/members/batwings/best.html
Camping/Caving - http://www.freeyellow.com/members/batwings/caving.html
Screw OPEC, drive a motorcycle!
>> I do thank you for the carpet tape. it is much sturder than some otherUnbelievable as it may sound, in one shop I've seen them stick a 4" round
>> forms of double stick stuff.
steel part 2" thick to the faceplate of a big Heald Red Head ID/OD grinder.
I told them if that part came off over a 12,000 RPM ID spindle, it would
kill somebody. And indeed the trial piece shifted alarmingly easily under
hand pressure. I flat refused the job, and they went to sequential clamping
first on OD and then on ID, to do both in one setup. Whew.
Regards, Hoyt
Anti-virus request: Please do not add this email addy to address books
Belfab CNC - http://www.freeyellow.com/members/belfab/belfab.html
US Best MC - http://www.freeyellow.com/members/batwings/best.html
Camping/Caving - http://www.freeyellow.com/members/batwings/caving.html
Screw OPEC, drive a motorcycle!
Discussion Thread
pleijnen
2002-05-23 08:54:03 UTC
DeskWinNC vs Flashcut?
Tim Goldstein
2002-05-23 09:05:25 UTC
Re: [CAD_CAM_EDM_DRO] DeskWinNC vs Flashcut?
Jim Avey
2002-05-23 10:32:50 UTC
RE: [CAD_CAM_EDM_DRO]floating z axis
JanRwl@A...
2002-05-23 12:08:45 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
JanRwl@A...
2002-05-23 12:10:14 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
wanliker@a...
2002-05-23 12:10:57 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
bwrfromuk
2002-05-23 12:40:34 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
JanRwl@A...
2002-05-23 12:50:07 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Bill Vance
2002-05-23 13:34:02 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Jim Avey
2002-05-23 13:34:39 UTC
RE: [CAD_CAM_EDM_DRO]floating z axis
Les Newell
2002-05-23 14:20:08 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Jim Avey
2002-05-23 14:34:54 UTC
RE: [CAD_CAM_EDM_DRO]floating z axis
William Scalione
2002-05-23 16:09:42 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
waynegramlich
2002-05-23 16:34:01 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
turbulatordude
2002-05-23 18:31:46 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
JanRwl@A...
2002-05-23 19:00:13 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
aspaguy
2002-05-23 19:50:18 UTC
Re: DeskWinNC vs Flashcut?
Chris L
2002-05-23 20:37:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: DeskWinNC vs Flashcut?
Chris L
2002-05-23 20:56:01 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Jon Elson
2002-05-23 21:40:49 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Nic van der Walt
2002-05-24 01:11:49 UTC
RE: [CAD_CAM_EDM_DRO]floating z axis
bjammin@i...
2002-05-24 05:05:05 UTC
tape, babay
bjammin@i...
2002-05-24 05:09:38 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
bwrfromuk
2002-05-24 08:29:10 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
JanRwl@A...
2002-05-24 08:49:33 UTC
Re: [CAD_CAM_EDM_DRO] tape, babay
JanRwl@A...
2002-05-24 08:53:20 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
reed_irion
2002-05-24 10:25:09 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Alan Marconett KM6VV
2002-05-24 11:06:02 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Nic van der Walt
2002-05-24 11:56:58 UTC
RE: [CAD_CAM_EDM_DRO]floating z axis
Alan Marconett KM6VV
2002-05-24 12:51:11 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
Alan Marconett KM6VV
2002-05-24 13:31:05 UTC
Re: [CAD_CAM_EDM_DRO]floating z axis
bjammin@i...
2002-05-24 15:25:13 UTC
Re: [CAD_CAM_EDM_DRO] tape, babay