Re: Conversion
Posted by
mariss92705
on 2002-06-21 16:57:51 UTC
Jan,
I cited my source. Blame them, I'm too busy ducking for cover!!!
Mariss
I cited my source. Blame them, I'm too busy ducking for cover!!!
Mariss
--- In CAD_CAM_EDM_DRO@y..., JanRwl@A... wrote:
> In a message dated 21-Jun-02 12:27:21 Central Daylight Time,
> mariss92705@y... writes:
>
>
> > I looked it up and I got 25.399999999999987300000000000006
>
> Mariss! In what 1927 era book? The S.I. DEFINITION is
25.40000... mm =
> 1.0 inch ! ! !
>
>
> [Non-text portions of this message have been removed]
Discussion Thread
James Owens
2002-06-21 03:49:05 UTC
Conversion
Dan Statman
2002-06-21 04:17:59 UTC
Re: [CAD_CAM_EDM_DRO] Conversion
paul_alz
2002-06-21 08:28:58 UTC
Re: Conversion
afogassa
2002-06-21 08:29:33 UTC
Re: Conversion
Jon Elson
2002-06-21 10:11:51 UTC
Re: [CAD_CAM_EDM_DRO] Conversion
mariss92705
2002-06-21 10:26:10 UTC
Re: Conversion
Dave Lantz
2002-06-21 10:28:50 UTC
RE: [CAD_CAM_EDM_DRO] Re: Conversion
mariss92705
2002-06-21 10:39:04 UTC
Re: Conversion
Dave Lantz
2002-06-21 10:43:12 UTC
RE: [CAD_CAM_EDM_DRO] Re: Conversion
Carlos Guillermo
2002-06-21 11:22:13 UTC
RE: [CAD_CAM_EDM_DRO] Re: Conversion
Bill Vance
2002-06-21 11:31:31 UTC
Re: [CAD_CAM_EDM_DRO] Conversion
Dan Statman
2002-06-21 13:00:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Conversion
Doug Harrison
2002-06-21 15:27:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Conversion
Steve Blackmore
2002-06-21 16:03:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Conversion
JanRwl@A...
2002-06-21 16:40:20 UTC
Re: [CAD_CAM_EDM_DRO] Conversion
JanRwl@A...
2002-06-21 16:50:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Conversion
mariss92705
2002-06-21 16:54:00 UTC
Re: Conversion
mariss92705
2002-06-21 16:57:51 UTC
Re: Conversion
paul_alz
2002-06-21 17:12:29 UTC
Re: Conversion
James Owens
2002-06-21 17:35:35 UTC
Re: [CAD_CAM_EDM_DRO] Conversion
mayfieldtm
2002-06-21 19:19:57 UTC
Re: [CAD_CAM_EDM_DRO] Conversion
vavaroutsos
2002-06-21 21:04:48 UTC
Re: Conversion
Brian Pitt
2002-06-21 22:46:45 UTC
Re: [CAD_CAM_EDM_DRO] Conversion
bjammin@i...
2002-06-22 06:20:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Conversion
JanRwl@A...
2002-06-22 20:44:58 UTC
Re: [CAD_CAM_EDM_DRO] Conversion
Steve Blackmore
2002-06-23 03:42:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Conversion