Re: [CAD_CAM_EDM_DRO] Re: Motors
Posted by
Gene
on 2002-07-12 11:04:24 UTC
I don't know the difference, is an 8 wire motor unipolar?
the_dutros wrote:
the_dutros wrote:
>
> --- In CAD_CAM_EDM_DRO@y..., Gene <capper@i...> wrote:
> > I'm going to replace my steppers with 4.5 amp, 2 volt, 8 wire
> motors.
> > I'm Going to wire them in parallel( if that's the best way?} I
> > calculate 20k 1/4 watt resistors for the 201 geckos power output. My
> > power supply is 62 volts. Is this correct ? if the volts are too
> high
> > how would I lower them?
>
> I'm just curious -- did you happen to have the motors, are they the
> only ones you could find, or are you actually going to buy them?
>
> I keep reading about people buying UNIPOLAR motors to be driven by
> circuits that are (essentially) designed for BIPOLAR motors. Why do
> you do this if you have a choice when a BIPOLAR motor with similar
> specifications will perform significantly better?
>
> To answer your question, there are several sites listed in previous
> posts that describe in great detail how to determine the correct
> voltage, and stepper sizing. I believe the "rule of thumb" is not to
> exceed 25 times the rated voltage. You can use more, but it won't
> gain you any additional performance, just heat.
>
> -DASH
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
PTENGIN@x...
1999-07-28 11:07:25 UTC
Re: Re: Motors
Brian Fairey
1999-07-28 11:26:11 UTC
Re: Re: Motors
Jon Elson
1999-07-28 13:35:08 UTC
Re: Re: Motors
PTENGIN@x...
1999-07-28 15:34:17 UTC
Re: Re: Motors
Robert Campbell
1999-07-28 19:37:51 UTC
Re: Re: Motors
Woody
2001-04-05 16:29:01 UTC
Motors
mariss92705@y...
2001-04-05 16:52:24 UTC
Re: Motors
Woody
2001-04-05 16:59:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
Randy Gordon-Gilmore
2001-04-05 17:27:49 UTC
Re: [CAD_CAM_EDM_DRO] Motors
Alan Marconett KM6VV
2001-04-05 17:29:27 UTC
Re: [CAD_CAM_EDM_DRO] Motors
Woody
2001-04-05 17:39:03 UTC
Re: [CAD_CAM_EDM_DRO] Motors
JanRwl@A...
2001-04-05 18:00:58 UTC
Re: [CAD_CAM_EDM_DRO] Motors
wanliker@a...
2001-04-05 20:41:56 UTC
Re: [CAD_CAM_EDM_DRO] Motors
mariss92705@y...
2001-04-05 21:05:55 UTC
Re: Motors
Jon Elson
2001-04-05 21:42:16 UTC
Re: [CAD_CAM_EDM_DRO] Motors
Tom Eldredge
2001-04-06 04:12:24 UTC
Re: [CAD_CAM_EDM_DRO] Motors
ballendo@y...
2001-04-06 04:58:49 UTC
Re: Motors
Woody
2001-04-06 06:53:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
Joe Vicars
2001-04-06 06:57:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
e.heritage@b...
2001-04-06 07:04:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
Gene
2002-07-11 23:49:09 UTC
Motors
the_dutros
2002-07-12 05:17:10 UTC
Re: Motors
Gene
2002-07-12 11:04:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
Tim Goldstein
2002-07-12 11:23:27 UTC
Re: [CAD_CAM_EDM_DRO]Motors
JanRwl@A...
2002-07-12 20:14:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
mayfieldtm
2002-07-12 23:05:35 UTC
Re: Motors
alex
2003-04-25 11:33:17 UTC
Re: [CAD_CAM_EDM_DRO] Motors
Alan Marconett KM6VV
2003-04-25 13:32:10 UTC
Re: [CAD_CAM_EDM_DRO] Motors
alex
2003-04-25 13:37:57 UTC
Re: [CAD_CAM_EDM_DRO] Motors
JanRwl@A...
2003-04-25 14:28:46 UTC
Re: [CAD_CAM_EDM_DRO] Motors
alex
2003-04-25 14:56:09 UTC
Re: [CAD_CAM_EDM_DRO] Motors
turbulatordude
2003-04-25 15:35:12 UTC
Re: Motors
alex
2003-04-25 15:53:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
alex
2003-04-25 16:00:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
JanRwl@A...
2003-04-25 16:34:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
km6vv
2003-04-26 10:32:59 UTC
Re: Motors
alex
2003-04-26 14:38:25 UTC
Re: [CAD_CAM_EDM_DRO] Motors
alex
2003-04-29 10:47:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
Chris
2003-04-29 18:20:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
Jon Elson
2003-04-29 22:38:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
mayfieldtm
2003-04-30 09:14:47 UTC
Re: Motors
Chris
2003-04-30 17:38:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motors
onecooltoolfool
2003-05-04 18:36:39 UTC
Motors
JanRwl@A...
2003-05-04 19:36:13 UTC
Re: [CAD_CAM_EDM_DRO] Motors
Jon Elson
2003-05-04 22:52:22 UTC
Re: [CAD_CAM_EDM_DRO] Motors
onecooltoolfool
2003-05-05 04:01:26 UTC
Re: Motors