Re: EDM
Posted by
Jon Elson
on 2000-02-16 22:03:02 UTC
Brian Fairey wrote:
and
a current of about 1/4 to 1/2 amp while zapping. The resistor was about
30
Ohms, so I got about 1 A when the electrode shorted out. It gave a
pretty
impressive buzzing sound and lit up under the fluid when the discharge
was
going. Your transformer should do fine.
Jon
> From: Brian Fairey <bfairey@...>I did my tap burning with 30 VDC at the raw supply before the resistor,
>
> What is the typical voltage for the spark discharge?Why do I ask?
> because I have a good xfmr with all the taps but it will only give
> 50vdc
> at 5A
and
a current of about 1/4 to 1/2 amp while zapping. The resistor was about
30
Ohms, so I got about 1 A when the electrode shorted out. It gave a
pretty
impressive buzzing sound and lit up under the fluid when the discharge
was
going. Your transformer should do fine.
Jon
Discussion Thread
Tim Goldstein
1999-06-19 23:19:54 UTC
EDM
George Potter
1999-06-20 06:41:08 UTC
Re: EDM
Pete Jarman
1999-06-20 10:41:25 UTC
Re: EDM
Tim Goldstein
1999-06-21 07:43:01 UTC
Re: EDM
psp@x...
1999-06-21 08:51:38 UTC
Re: EDM
Tim Goldstein
1999-07-16 15:37:43 UTC
Re: EDM
TADGUNINC@x...
1999-07-16 18:11:51 UTC
Re: EDM
Scott Acorn
1999-07-17 17:07:53 UTC
Re: EDM
Scott Acorn
1999-07-17 18:09:08 UTC
Re: EDM
Jon Anderson
1999-07-17 18:14:31 UTC
Re: EDM
Tim Goldstein
1999-07-18 15:26:09 UTC
RE: EDM
Tim Goldstein
1999-07-18 15:32:47 UTC
RE: EDM
Mo
1999-07-18 14:41:03 UTC
Re: EDM
Tim Goldstein
1999-07-18 17:22:08 UTC
RE: EDM
J Catmull
1999-07-28 08:06:45 UTC
Re: EDM
Brian Fairey
2000-02-16 16:36:26 UTC
EDM
Jon Elson
2000-02-16 22:03:02 UTC
Re: EDM
tommy40010
2002-12-03 05:58:56 UTC
EDM
Jon Elson
2002-12-03 10:33:03 UTC
Re: [CAD_CAM_EDM_DRO] EDM
Tommy Sullivan
2002-12-03 16:13:25 UTC
Re: [CAD_CAM_EDM_DRO] EDM
Jon Elson
2002-12-13 00:17:14 UTC
Re: [CAD_CAM_EDM_DRO] EDM
JanRwl@A...
2002-12-13 09:55:23 UTC
Re: [CAD_CAM_EDM_DRO] EDM
turbulatordude <davemucha@j...
2002-12-13 10:23:49 UTC
Re: EDM
wanliker@a...
2002-12-13 16:37:27 UTC
Re: [CAD_CAM_EDM_DRO] EDM
Steve
2002-12-13 22:24:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM
Hoyt McKagen
2002-12-14 04:47:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM
wanliker@a...
2002-12-14 08:46:54 UTC
EDM
wanliker@a...
2002-12-14 09:18:10 UTC
EDM
Jay Hayes
2002-12-14 10:27:03 UTC
Re: [CAD_CAM_EDM_DRO] EDM
JanRwl@A...
2002-12-14 18:36:23 UTC
Re: [CAD_CAM_EDM_DRO] EDM
RichD
2002-12-14 19:04:24 UTC
Re: [CAD_CAM_EDM_DRO] EDM
JanRwl@A...
2002-12-14 20:21:38 UTC
Re: [CAD_CAM_EDM_DRO] EDM
Ian W. Wright
2002-12-17 02:17:50 UTC
Re: EDM
Steve
2002-12-17 07:47:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM