CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] EMC Question

Posted by Tim Goldstein
on 2003-09-01 14:59:47 UTC
> -----Original Message-----
>
> Setting up BDI 2.18 I was getting a "Axis 0 following error".
> Anyone have any specific direction I should go to avoid this
> error? Also, which Motion Control Module is best for G320's
> with SEM MT30H4 Servos on a Bridgeport style Machine.
> I was using Freqmod.o Is there a better module to use?

If it is still in the distribution, use steppermod.o. Gecko G320/340's
don't care about the more even the pulse spacing that you get with
freqmod.o due to the way the pulse is only used to drive an accumulator.
Steppermod.o takes less resources, can put out a faster pulse stream,
and does not have all the hassles of tuning to eliminate the software
induced follow errors that are so common with freqmod.o

Tim
[Denver, CO]
Beat the Sherline Oct 1 price increase, Buy Now!

Sherline & Taig products at Deep Discount
Mach1 & DeskCNC with credit card ordering
www.KTMarketing.com/Sherline
e-mail me at Timg @ KTMarketing.com for items not yet listed

Discussion Thread

cnc@p... 2001-08-05 06:08:21 UTC EMC Question Paul 2001-08-05 07:36:40 UTC Re: [CAD_CAM_EDM_DRO] EMC Question cnc@p... 2001-08-05 07:56:34 UTC Re: EMC Question cnc@p... 2001-08-05 10:47:47 UTC Re: EMC Question William Scalione 2001-08-05 12:13:27 UTC Re: [CAD_CAM_EDM_DRO] Re: EMC Question Stephen Goldsmith 2001-08-05 12:27:27 UTC Re: [CAD_CAM_EDM_DRO] Re: EMC Question Tim Goldstein 2001-08-05 12:33:35 UTC RE: [CAD_CAM_EDM_DRO] Re: EMC Question William Scalione 2001-08-05 13:10:45 UTC Re: [CAD_CAM_EDM_DRO] Re: EMC Question tomp_tag 2003-09-01 13:32:00 UTC Re: [CAD_CAM_EDM_DRO] EMC Question Paul 2003-09-01 14:40:40 UTC Re: [CAD_CAM_EDM_DRO] EMC Question Vince Negrete 2003-09-01 14:49:52 UTC Re: [CAD_CAM_EDM_DRO] EMC Question Tim Goldstein 2003-09-01 14:59:47 UTC RE: [CAD_CAM_EDM_DRO] EMC Question Vince Negrete 2003-09-01 16:31:08 UTC Re: [CAD_CAM_EDM_DRO] EMC Question alex 2004-01-24 16:57:06 UTC Re: [CAD_CAM_EDM_DRO] Re: EMC Question jlsmith269 2004-01-24 18:44:07 UTC Re: EMC Question ccq@x... 2004-01-24 23:19:55 UTC Re: [CAD_CAM_EDM_DRO] Re: EMC Question Thomas Fritz 2004-01-25 00:06:08 UTC Re: [CAD_CAM_EDM_DRO] Re: EMC Question Raymond Heckert 2004-01-25 15:51:49 UTC Re: [CAD_CAM_EDM_DRO] Re: EMC Question Victor A. Estes 2006-07-17 08:47:26 UTC EMC Question Anders Wallin 2006-07-17 09:39:54 UTC Re: [CAD_CAM_EDM_DRO] EMC Question