Re: [CAD_CAM_EDM_DRO] EMC Question
Posted by
Vince Negrete
on 2003-09-01 16:31:08 UTC
Hi Tim,
I did try to set 'steppermod.o' in emc.ini and it aborts with File Not
Found. I found 'univstepmod.o' in the module directory but when I enable
that one it replies in the console with Unresolved Symbol errors and aborts
EMC.
Seems about the only one that works properly is freqmod.o. I'm thinking
that I'm missing something since emc.ini was setup for use with Servo-To-Go
Card.
So, when I use another module what else do I need to change? Does anyone
have a sample emc.ini I can look at to compare with that uses steppermod.o ?
Thanks Tim for the reply. This morning I printed the "installemc.htm" from
your site. Havent had time to go through it fully but I'm wondering if I
can apply the ideas to setting up newer versions dated after May 2001 (the
BDI 2.2.18 release).
Vince
I did try to set 'steppermod.o' in emc.ini and it aborts with File Not
Found. I found 'univstepmod.o' in the module directory but when I enable
that one it replies in the console with Unresolved Symbol errors and aborts
EMC.
Seems about the only one that works properly is freqmod.o. I'm thinking
that I'm missing something since emc.ini was setup for use with Servo-To-Go
Card.
So, when I use another module what else do I need to change? Does anyone
have a sample emc.ini I can look at to compare with that uses steppermod.o ?
Thanks Tim for the reply. This morning I printed the "installemc.htm" from
your site. Havent had time to go through it fully but I'm wondering if I
can apply the ideas to setting up newer versions dated after May 2001 (the
BDI 2.2.18 release).
Vince
----- Original Message -----
From: "Tim Goldstein" <timg@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Monday, September 01, 2003 2:59 PM
Subject: RE: [CAD_CAM_EDM_DRO] EMC Question
> > -----Original Message-----
> >
> > Setting up BDI 2.18 I was getting a "Axis 0 following error".
> > Anyone have any specific direction I should go to avoid this
> > error? Also, which Motion Control Module is best for G320's
> > with SEM MT30H4 Servos on a Bridgeport style Machine.
> > I was using Freqmod.o Is there a better module to use?
>
> If it is still in the distribution, use steppermod.o. Gecko G320/340's
> don't care about the more even the pulse spacing that you get with
> freqmod.o due to the way the pulse is only used to drive an accumulator.
> Steppermod.o takes less resources, can put out a faster pulse stream,
> and does not have all the hassles of tuning to eliminate the software
> induced follow errors that are so common with freqmod.o
>
> Tim
> [Denver, CO]
> Beat the Sherline Oct 1 price increase, Buy Now!
>
> Sherline & Taig products at Deep Discount
> Mach1 & DeskCNC with credit card ordering
> www.KTMarketing.com/Sherline
> e-mail me at Timg @ KTMarketing.com for items not yet listed
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
Discussion Thread
cnc@p...
2001-08-05 06:08:21 UTC
EMC Question
Paul
2001-08-05 07:36:40 UTC
Re: [CAD_CAM_EDM_DRO] EMC Question
cnc@p...
2001-08-05 07:56:34 UTC
Re: EMC Question
cnc@p...
2001-08-05 10:47:47 UTC
Re: EMC Question
William Scalione
2001-08-05 12:13:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Question
Stephen Goldsmith
2001-08-05 12:27:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Question
Tim Goldstein
2001-08-05 12:33:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: EMC Question
William Scalione
2001-08-05 13:10:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Question
tomp_tag
2003-09-01 13:32:00 UTC
Re: [CAD_CAM_EDM_DRO] EMC Question
Paul
2003-09-01 14:40:40 UTC
Re: [CAD_CAM_EDM_DRO] EMC Question
Vince Negrete
2003-09-01 14:49:52 UTC
Re: [CAD_CAM_EDM_DRO] EMC Question
Tim Goldstein
2003-09-01 14:59:47 UTC
RE: [CAD_CAM_EDM_DRO] EMC Question
Vince Negrete
2003-09-01 16:31:08 UTC
Re: [CAD_CAM_EDM_DRO] EMC Question
alex
2004-01-24 16:57:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Question
jlsmith269
2004-01-24 18:44:07 UTC
Re: EMC Question
ccq@x...
2004-01-24 23:19:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Question
Thomas Fritz
2004-01-25 00:06:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Question
Raymond Heckert
2004-01-25 15:51:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Question
Victor A. Estes
2006-07-17 08:47:26 UTC
EMC Question
Anders Wallin
2006-07-17 09:39:54 UTC
Re: [CAD_CAM_EDM_DRO] EMC Question